ERROR-121 | ERROR-122 | ERROR-123 | ERROR-124 | ERROR-125 | ERROR-126 | ERROR-127 | ERROR-128 | ERROR-129 | ERROR-130 | ERROR-131 | ERROR-132 | ERROR-133| ERROR-121 | Parameter MTYPE must be set to ETBROKER or MQSERIES |
| Explanation |
An invalid value was specified for the MTYPE parameter of the ADAMTS utility. |
| Action |
Check the parameter input, correct the error, and rerun the job. |
| ERROR-122 | Parameter ETBROKERID must be specified when MTYPE=ETBROKER Parameter ETBSERVICE must be specified when MTYPE=ETBROKER Parameter ETBSERVICENAME must be specified when TYPE=ETBROKER Parameter ETBSERVICECLASS must be specified when MTYPE=ETBROKER Parameter MQQNAME must be specified when MTYPE=MQSERIES Parameter MQQMGRNAME must be specified when MTYPE=MQSERIES |
| Explanation |
The listed, required parameters are missing for the selected MTYPE. |
| Action |
Check the parameter input, correct the error, and rerun the job. |
| ERROR-123 | ETBROKER parameters may not be specified when MTYPE=MQSERIES MQSeries parameters may not be specified when MTYPE=ETBROKER |
| Explanation |
Improper parameters have been specified for the selected MTYPE. |
| Action |
Check the parameter input, correct the error, and rerun the job. |
| ERROR-124 | Open failed for file MTSIN |
| Explanation |
The file allocated by the MTSIN DD statement could not be opened. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-125 | Load failed for {ADAETB|ADAMQS} |
| Explanation |
The module listed could not be loaded by the job. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-126 | INIT call failed. Return code rcrc, Reason code reason |
| Explanation |
The INIT call failed for the selected MTYPE. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-127 | CONNECT call failed “Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code” |
| Explanation |
The CONNECT call failed for the selected MTYPE. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-128 | OPEN call failed. “Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code” |
| Explanation |
The OPEN call failed for the selected MTYPE. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-129 | SEND call failed. “Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code” |
| Explanation |
The SEND call failed for the selected MTYPE. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-130 | CLOSE call failed. “Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code” |
| Explanation |
The CLOSE call failed for the selected MTYPE. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-131 | DISCONNECT call failed. “Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code” |
| Explanation |
The DISCONNECT call failed for the selected MTYPE. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-132 | TERM call failed. Return code xxxxxxxx Reason code xxxxxxxx |
| Explanation |
The TERM call failed for the selected MTYPE. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
| ERROR-133 | Read of MTSIN failed |
| Explanation |
A problem occurred while attempting to read MTSIN. The cause is probably a JCL error. |
| Action |
Check the job output or JCL, correct the error, and rerun the job. |
