Version 8.1.4
 —  Messages and Codes  —

ADAMTR Error Messages

Overview of Messages

ERROR-121 | ERROR-122 | ERROR-123 | ERROR-124 | ERROR-125 | ERROR-126 | ERROR-127 | ERROR-128 | ERROR-129 | ERROR-130 | ERROR-131 | ERROR-132 | ERROR-133 | ERROR-134

ERROR-121 Parameter MTYPE must be set to ETBROKER or MQSERIES
Explanation

An invalid value was specified for the MTYPE parameter of the ADAMTR utility.

Action

Check the parameter input, correct the error, and rerun the job.


ERROR-122 Parameter ETBROKERID must be specified when MTYPE=ETBROKER
Parameter ETBSERVICE must be specified when MTYPE=ETBROKER
Parameter ETBSERVICENAME must be specified when TYPE=ETBROKER
Parameter ETBSERVICECLASS must be specified when MTYPE=ETBROKER
Parameter MQQNAME must be specified when MTYPE=MQSERIES
Parameter MQQMGRNAME must be specified when MTYPE=MQSERIES
Explanation

The listed, required parameters are missing for the selected MTYPE.

Action

Check the parameter input, correct the error, and rerun the job.


ERROR-123 ETBROKER parameters may not be specified when MTYPE=MQSERIES
MQSeries parameters may not be specified when MTYPE=ETBROKER
Explanation

Improper parameters have been specified for the selected MTYPE.

Action

Check the parameter input, correct the error, and rerun the job.


ERROR-124 Load failed for {ADAETB|ADAMQS}
Explanation

The module listed could not be loaded by the job.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-125 INIT call failed. Return code rcrc, Reason code reason
Explanation

The INIT call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-126 CONNECT call failed
Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code
Explanation

The CONNECT call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-127 OPEN call failed.
Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code
Explanation

The OPEN call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-128 RECEIVE call failed.
Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code
Explanation

The RECEIVE call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-129 BACKOUT call failed.
Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code
Explanation

The BACKOUT call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-130 COMMIT call failed.
Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code
Explanation

The COMMIT call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-131 CLOSE call failed.
Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code
Explanation

The CLOSE call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-132 DISCONNECT call failed.
Return-code” “reason-code” “messaging-system-return-code” “messaging-system-reason-code
Explanation

The DISCONNECT call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-133 TERM call failed. Return code xxxxxxxx Reason code xxxxxxxx
Explanation

The TERM call failed for the selected MTYPE.

Action

Check the job output or JCL, correct the error, and rerun the job.


ERROR-134 Parameter PRINT must be set to YES or NO
Explanation

An invalid value was specified for the PRINT parameter of the ADAMTR utility.

Action

Check the parameter input, correct the error, and rerun the job.


Top of page