EntireX Version 9.7
 —  Administration of EntireX under BS2000/OSD  —

Setting up Broker Instances

This document contains information on setting up the Broker under BS2000/OSD. It assumes that you have completed the relevant steps described under Installing EntireX under BS2000/OSD. It covers the following topics:


Setting up TCP/IP Transport

The recommended way to set up the TCP/IP communicator is to define PORT=nnnn and optionally HOST=x.x.x.x|hostname under TCP/IP-specific Attributes under Broker Attributes.

However, if no port number is specified in the Broker attribute file, the broker kernel will default port number of 1971. This is the same default port number that the stubs use.

Top of page

Setting up Entire Net-Work/Adabas SVC Transport

Start of instruction setTo set up EntireX Net-Work communication mechanism

  1. Ensure that appropriate values are supplied in the broker attribute file section DEFAULTS=NET, paying particular attention to the IUBL parameter - which specifies the maximum send/receive buffer length that can be sent between an application and Broker kernel within a single request - and NABS, which governs the total amount of storage available concurrently for all users communicating over this transport mechanism. See Adabas SVC/Entire Net-Work-specific Attributes under Broker Attributes.

  2. Ensure that communication with the broker is possible by running the installation verification programs (bcoc, bcos) using transport type NET.

Top of page

Starting and Stopping the Broker

Starting the Broker

Start of instruction setTo start the broker

Stopping the Broker

Start of instruction setTo stop the broker from a privileged user ID

Start of instruction setTo stop the broker from an operator console

Start of instruction setTo stop the broker from a non-privileged user ID

Top of page

Tracing EntireX Broker

This section covers the following topics:

Broker TRACE-LEVEL Attribute

The Broker TRACE-LEVEL attribute determines the level of tracing to be performed while Broker is running. The Broker has a master TRACE-LEVEL specified in the Broker section of the attribute file as well as several individual TRACE-LEVEL settings that are specified in the following sections of the attribute file. You can also modify the different TRACE-LEVEL values while Broker is running, without having to restart the Broker kernel for the change to take effect.

Individual Settings Specified in Attribute File Section
Master trace level DEFAULTS=BROKER
Persistent Store trace level DEFAULTS=ADABAS
Conversion trace level Trace option of the CONVERSION parameter that can be defined in DEFAULTS=SERVICE | TOPIC
Security trace level DEFAULTS=SECURITY
Transport trace level DEFAULTS=NET | TCP | SSL

These individual TRACE-LEVEL values determine the level of tracing within each subcomponent. If not specified, the master TRACE-LEVEL is used.

Trace messages are written to the SYSOUT file of the EntireX Broker common output manager (COM) task.

Attribute File Trace Setting

Trace Level Description
0 No tracing. Default value.
1 Traces incoming requests, outgoing replies, and resource usage.
2 All of Trace Level 1, plus all main routines executed.
3 All of Trace Level 2, plus all routines executed.
4 All of Trace Level 3, plus Broker ACI control block displays.
8 All of Trace Level 4, plus Adabas Persistent Store Adabas control blocks.

Note:
Trace levels 2 and above should be used only when requested by Software AG support.

Deferred Tracing

It is not always convenient to run with TRACE-LEVEL defined, especially when higher trace levels are involved. Deferred tracing is triggered when a specific condition occurs, such as an ACI response code or a broker subtask abend. Such conditions cause the contents of the trace buffer to be written, showing trace information leading up the specified event. If the specified event does not occur, the Broker trace will contain only startup and shutdown information (equivalent to TRACE-LEVEL=0). Operating the trace in this mode requires the following additional attributes in the broker section of the attribute file. Values for TRBUFNUM and TRAP-ERROR are only examples.

Attribute Value Description
TRBUFNUM 3 Specifies the deferred trace buffer size = 3 * 64 K.
TRMODE WRAP Indicates trace is not written until an event occurs.
TRAP-ERROR 322 Assigns the event ACI response code 00780322 "PSI: UPDATE failed".

Top of page

Protecting a Broker against Denial-of-Service Attacks

An optional feature of EntireX Broker is available to protect a broker running with SECURITY=YES against denial-of-service attacks. An application that is running with invalid user credentials will get a security response code. However, if the process is doing this in a processing loop, the whole system could be affected. If PARTICIPANT-BLACKLIST is set to YES, EntireX Broker maintains a blacklist to handle such "attacks". If an application causes ten consecutive security class error codes within 30 seconds, the blacklist handler puts the participant on the blacklist. All subsequent requests from this participant are blocked until the BLACKLIST-PENALTY-TIME has elapsed.

Server Shutdown Use Case

Here is a scenario illustrating another use of this feature that is not security-related.

An RPC server is to be shut down immediately, using Broker Command and Information Services (CIS), and has no active request in the broker. The shutdown results in the LOGOFF of the server. The next request that the server receives will probably result in message 00020002 "User does not exist", which will cause the server to reinitialize itself. It was not possible to inform the server that shutdown was meant to be performed.

With the blacklist, this is now possible. As long as the blacklist is not switched off, when a server is shut down immediately using CIS and when there is no active request in the broker, a marker is set in the blacklist. When the next request is received, this marker results in message 00100050 "Shutdown IMMED required", which means that the server is always informed of the shutdown.

Top of page