This page explains unit of work and persistence messages from the EntireX Broker Log and Console. These messages have the format:
ETBWnnnn
| where | ETBW | is the message class, and |
| nnnn | is the message number in the range 0000-9999 |
ETBW0138 | ETBW0145 | ETBW0313 | ETBW0314 | ETBW0317 | ETBW0318 | ETBW0330 | ETBW0331 | ETBW0332 | ETBW0333 | ETBW0334 | ETBW0349 | ETBW0354 | ETBW0426 | ETBW0429 | ETBW0506 | ETBW0517 | ETBW0521 | ETBW0526 | ETBW0535 | ETBW0536 | ETBW0537 | ETBW0545 | ETBW0595 | ETBW0607 | ETBW0616 | ETBW0618 | ETBW0640 | ETBW0663 | ETBW0684| ETBW0138 | PSI: Maximum Extents used for Cell Pool |
| Explanation |
The Broker detected that the persistent store has no more cells available for cell pool xxxxxxxx (see diagnostic message ETBD0286 next to additional info for the name of the cell pool) and the maximum number of extents have been reached. |
| Action |
Review the persistent store startup parameters and increase the initial allocation value for the exhausted cell pool. For the new value to take effect, you must cold start the persistent store and restart the Broker. |
| ETBW0145 | PSI: Attempt to expand beyond Dataspace Boundary |
| Explanation |
The Broker attempted to expand the persistent store beyond the dataspace boundary. |
| Action |
Review the persistent store startup parameter for dataspace pages and increase accordingly to an appropriate value. Restart the Broker. Use the System Management Hub to monitor usage in the persistent store. |
| ETBW0313 | Broker RESTART failed |
| Explanation |
During broker startup, an error has been detected during the restart processing phase. |
| Action |
Examine the EntireX Broker log. Determine the cause of the error. Correct the error and restart the Broker. If the cause cannot be determined, contact Software AG support. |
| ETBW0314 | API: UOW status invalid |
| Explanation |
The unit of work status code is not a recognized value. |
| Action |
This is probably an internal EntireX Broker error. Contact Software AG support. |
| ETBW0317 | PSI: Persistent Store termination failed |
| Explanation |
An attempt to shut down the persistent store failed. |
| Action |
None. |
| ETBW0318 | PSI: Function input parms invalid |
| Explanation |
The requested persistent store function is not supported by the PSTORE handler. The request is ignored. |
| Action |
Contact Software AG support. |
| ETBW0330 | PSI: Restart-Temp Msg File Open Failed |
| Explanation |
This is an internal error. |
| Action |
Contact Software AG support. |
| ETBW0331 | PSI: Restart-Temp Msg IDX Open Failed |
| Explanation |
This is an internal error. |
| Action |
Contact Software AG support. |
| ETBW0332 | PSI: Restart-Msg Index Length Zero |
| Explanation |
This is an internal error. |
| Action |
Contact Software AG support. |
| ETBW0333 | PSI: Restart-Msg File Read Failure |
| Explanation |
This is an internal error. |
| Action |
Contact Software AG support. |
| ETBW0334 | PSI: Restart-Temp Msg File Write Failure |
| Explanation |
This is an internal error. |
| Action |
Contact Software AG support. |
| ETBW0349 | Publish and Subscribe is not licensed |
| Explanation |
Make sure that your license file contains entries that allow you to use the Publish and Subscribe feature. |
| Action |
Contact Software AG support. |
| ETBW0354 | EntireX License Key Error |
| Explanation |
Your EntireX License has expired. |
| Action |
Please contact your local Software AG office or distributor to extend your license. |
| ETBW0426 | Start of ETB_SHUTDOWN thread failed |
| Explanation |
UNIX/Windows only. The "etbnuc" process encountered an error while creating shutdown thread. Broker could not be initialized. |
| Action |
Contact Software AG support. |
| ETBW0429 | Missing or invalid XTI library |
| Explanation |
One of the components of Entire Net-Work communicator is missing. |
| Action |
Contact Software AG support. |
| ETBW0506 | ** Communicator not available anymore ** |
| Explanation |
The Communication Manager of the transport layer stops due to unrecoverable errors, exceeded retry limit or shutdown. |
| Action |
Check the log file for error messages. Ignore this warning if shutdown was requested. |
| ETBW0517 | Terminate Restart Handling |
| Explanation |
The Communication Manager did not succeed to run the transport-specific Communicator. All attempts to restart the Communicator were not successful. |
| Action |
Check the log file for error messages. |
| ETBW0521 | Unexpected Communicator Nucleus Status |
| Explanation |
A component of the transport layer detected an unexpected status and will stop immediately. |
| Action |
Check the log file for error messages or shutdown. |
| ETBW0526 | Broker kernel not running with Security |
| Explanation |
An operator command was issued that interacts with Broker's security component. However, security was not activated for this Broker. |
| Action |
Do not issue security relevant operator commands without activating security. |
| ETBW0535 | PSTORE is not licensed |
| Explanation |
Make sure that your license file contains entries that allow you to use the persistent store for the Publish/Subscribe feature. |
| Action |
Contact Software AG support. |
| ETBW0536 | SUBSCRIBER-STORE is disabled |
| Explanation |
The subscriber store is configured to use the primary store, and the primary store is not licensed. |
| Action |
Contact Software AG support. |
| ETBW0537 | Ambiguous: CONVERSION and TRANS |
| Explanation |
Broker detected that attributes of the indicated service (or topic) specify both
|
| Action |
If you still want the service (or topic) to use |
| ETBW0545 | EntireX License Status License expiration date is yyyy/mm/dd . License will expire in nn days - or - License expired on yyyy/mm/dd |
| Explanation |
Indicates the expiration date of your EntireX license. If the expiration date is less than 30 days in the future but greater than 0, you are reminded to contact Software AG. If the license has expired, you will not be able to restart. |
| Action |
Please contact your local Software AG office or distributor to extend your license. |
| ETBW0595 | PSILIB: PSTORE-TYPE=FILE is unsupported |
| Explanation |
|
| Action |
Migrate the data of the persistent store of type file to a different persistent store type. See Migrating the Persistent Store. |
| ETBW0607 | Command logging switched off |
| Explanation |
Command logging was requested. However, it is not possible to switch on command logging due to configuration errors. |
| Action |
Fix the problem and switch on command logging. |
| ETBW0616 | CPU limit reached |
| Explanation |
The CPU time of the task is exceeded. Broker received the interrupt from the operating system and will go down. |
| Action |
Specify a TIME=1440 parameter for the JCL |
| ETBW0618 | Transport not active |
| Explanation |
The transport-specific operator command cannot be executed. The transport is currently not active. |
| Action |
Issue the operator command when the transport is active. |
| ETBW0640 | EntireX License Key Warning |
| Explanation |
A warning occurred while processing the EntireX License file. Additional error test will provide more information. |
| Action |
Consult the additional error text and take appropriate action. |
| ETBW0663 | No assignment for LICENSE Report |
| Explanation |
Under z/OS and BS2000/OSD, the license is printed during startup. However, the assignment for the license report output file is missing. |
| Action |
Assign the license report output file. |
| ETBW0684 | Cannot make Broker non-swappable |
| Explanation |
Broker not APF-authorized. |
| Action |
Ensure that all load libraries in the Broker kernel steplib are APF-authorized. |
