Apama Analytics Builder 10.6.6 | Using Apama Analytics Builder for Cumulocity IoT | Using the Model Editor | Working with blocks and wires | Editing the parameters of a block
 
Editing the parameters of a block
Most blocks (but not all) have parameters that you have to set according to your requirements.
When Missing is shown on an input or output block on the canvas, this means that the defined device, device group or asset cannot be found in the Cumulocity IoT inventory. You should then either go to the Cumulocity IoT inventory and make sure that this device is registered or that the device group or asset exists, or you should select a different, existing device, device group or asset in the block parameter editor (see below).
The labels of some blocks on the canvas show the value of the most important parameter. For example, the Expression block shows the defined expression, and the Time Delay block shows the defined delay in seconds.
The block parameter editor also contains commands for duplicating and deleting the currently selected block. See Duplicating a block and Deleting a block or wire for detailed information.
For the input and output blocks, you can globally replace the devices, device groups or assets that are used. See Replacing devices, device groups and assets for detailed information.
*To edit the parameters of a block
1. On the canvas of the model editor, click the block that you want to edit using the left mouse button.
The block parameter editor appears, providing input fields for all parameters that can be specified for that block.
2. For some blocks (such as an input block or output block for a device), the block parameter editor shows a Block Type drop-down list box. Select the type of block that is appropriate for your requirements.
Note:
The following applies when you change the block type for a block that is already wired to one or more other blocks: if the new block type has different port names (for example, if the port name changes from Value to Value 1), the existing wires to/from the changed ports are removed. This is done because a changed port name would make the existing wiring invalid.
3. For the input and output blocks, you can select a different device (for input or output), device group (for input only) or an asset (if the search box is used) from a dialog box.
By default, 10 devices and 10 device groups are shown, sorted alphabetically. With a large inventory, you will have to click Load more to display any devices or device groups that are not shown initially.
The tree in the dialog box reflects the parent/child hierarchy in the Cumulocity IoT inventory. The list of devices includes any defined child devices, and the list of device groups includes any defined sub-groups. These are available from expandable/collapsible nodes. For output blocks, you can also select a Trigger Device.
The search box can be used to show any assets in the Cumulocity IoT inventory which match your search criteria. This includes devices, device groups and also managed objects. The search is case-sensitive. The characters that you type in may be contained at any position within the name. The tree is updated with each character that you type. With a large search result, you will have to click Load more to display any assets that are initially not shown.
Click the Use button (this is shown when you move the mouse over an entry) to select the device, device group or asset that you want to use. For output blocks, you cannot select a device group, but you can select any device within that group.
The maximum number of shown devices, device groups and/or assets depends on a tenant option. For more information, see Configuring the number of shown devices, device groups and/or assets.
The assets that are shown when searching also depend on a tenant option. You can restrict the search to show only assets of a specific type. For more information, see Searching for input and output assets.
4. For some blocks (such as the Range Lookup block), the block parameter editor shows text boxes for specifying key-value pairs. If you need to specify more key-value pairs, click Add row. The key-value pair in the first row is processed first. You can drag a row to a different position using the control that is shown next to that row, and you can delete a row that you do not need any more by clicking next to that row. Empty rows are automatically removed when you leave the block parameter editor.
5. Specify all required parameters.
Detailed reference information for each block (and block type) is available from the documentation pane. See also Viewing the documentation for a block.
Your input is kept in memory when you leave the block parameter editor (for example, when you click on another block or the canvas).
Note:
Keep in mind that your changes are only written to the inventory when you save the model. See also Saving a model.