An active Natural session uses CICS resources such as thread storage, roll facility entries (that is, records in a VSAM RRDS file, in a CICS temporary storage queue or main memory) as well as swap pool slots or Roll Server slots. These resources are allocated by Natural CICS Interface and correctly released whenever a session under control of Natural CICS Interface terminates normally or abnormally.
If a Natural session termination is not controlled by Natural CICS Interface, a node error program helps to correctly release the acquired resources.
This Dokument discusses CICS node error program considerations.
The following topics are covered:
See also:
For information on installing a CICS node error program, refer to the corresponding section in Installing Natural CICS Interface on z/OS or Installing Natural CICS Interface on z/VSE in the Natural Installation documentation.
In the following situations, Natural CICS Interface does not receive control at session termination and, therefore, cannot properly release the resources still held by the session:
A non-Natural program called by Natural issues an
EXEC CICS ABEND CANCEL command to terminate the CICS
task abnormally.
Some CICS monitor products offer tools to purge CICS tasks, thus bypassing any abnormal termination exit set by the application.
A user disconnects a terminal from the CICS region (by switching the power off or using an adequate session manager function) while the respective Natural session is not active in CICS (pseudo-conversational screen I/O) at that time.
Natural CICS Interface provides some recovery mechanisms to recover from such situations.
For example:
Whenever a new Natural session is to be started, Natural checks whether another session with the same terminal ID is active. If such a session exists, it is logically terminated, and all its resources are released prior to starting the new session.
However, if COMARET=OFF
is set in the NTCICSP macro, the information to resume a Natural
session is kept in a CICS temporary storage record where the terminal ID is
part of the storage queue name. As a result, another CICS user who tries to
start a Natural session with this terminal ID will resume the old session
rather than starting a new session.
CICS provides the node error program (NEP) exit interface
DFHZNEP, which is called when a user disconnects a terminal from
the CICS region. The session is lost if the user disconnects the terminal while
the respective Natural session is not active in CICS. You can then use
DFHZNEP to execute the Natural-specific
NCIZNEP node
error program and terminate the lost session. This program is delivered with
Natural CICS Interface (see also Natural
CICS Sample Programs).
NCIZNEP tries to resume a session asynchronously and
subsequently terminate it logically based on the session restart information
(NEXTTRANSID and restart data in COMMAREA or CICS
temporary storage) of a terminal session with pending pseudo-conversational
screen I/O.
Upon completion, NCIZNEP cleans the parameter input
indicating to the caller (usually DFHZNEP) whether it has
successfully completed its work and launches the cleanup task for the Natural
session.
If more than one Natural CICS Interface version is active in a CICS
system, cleanup processing performed by the called Natural version-specific
node error program can fail, because the Natural session to be terminated is
hosted by a different Natural CICS Interface version. Upon execution completion
of NCIZNEP, DFHZNEP can test whether the operation
was successful. If the operation was not successful, NCIZNEP will
call another node error program related to a different Natural CICS Interface
version.
If a user disconnects a terminal from the CICS region while the
respective Natural session is not active in CICS, DFHZNEP can
receive control more than once for various internal error codes, since each
internal error code is related to a specific CICS error message.
If you want NCIZNEP to attempt to immediately purge a
currently active Natural session for which NCIZNEP receives
control, specify PURGE=YES for the NCIZNEP module
link. See the installation procedure for Natural CICS Interface and the section
CICS Startup Parameters in
Installing Natural CICS
Interface on z/OS or
Installing Natural CICS
Interface on z/VSE in the Natural
Installation documentation.
In general, the following is required for MRO/CICSPlex environments:
DFHZNEP and NCIZNEP must be
installed in the TOR.
The NCIZNEP module must be defined in CICS with
EXECKEY(CICS).
For MRO/CICSPlex environments where you want NCIZNEP
to purge a currently active Natural session, consider the following additional
requirements:
The NCIZNEP module must also be defined in the
CICS AORs associated with a TOR.
A transaction ID must be defined for the NCIZNEP
module in the CICS TOR and the AORs with the attributes
TASKDATAKEY(CICS) and PRIORITY(255)
The transaction ID must also be specified with the
NEPTRAN parameter in the CICS startup parameters in the
NCIZNEP module as described in
Installing
Natural CICS Interface on z/OS or
Installing
Natural CICS Interface on z/VSE in the Natural
Installation documentation.
The Natural transactions for which you want to purge currently
active Natural sessions have to be defined in CICS with the attribute
SPURGE(YES).
If you want to call the node error programs NCIZNEP
(for Natural CICS Interface) and CORNEP (for Adabas
System Coordinator) from DFHZNEP, you
should consider that both NCIZNEP and CORNEP may
attempt to release Adabas-related resources at the same time. In order to avoid
interferences due to concurrent execution, always call NCIZNEP
before CORNEP and slightly delay the start time of
CORNEP to make sure that NCIZNEP has completed before
CORNEP starts executing.
For more information, see the Adabas System Coordinator Installation documentation.
The source library of Natural CICS Interface contains the
XNCINEP2 sample node error program
for CICS which provides the following options:
XNCINEP2 enables an error processor to receive
control for all possible error codes passed to DFHZNEP. If
XNCINEP2 receives control, it issues a CICS trace request that
shows with which error codes DFHZNEP has been invoked on certain
actions and related TCTTE error information.
XNCINEP2 calls the NCIZNEP module
via EXEC CICS LINK, which performs a Natural session cleanup.
If DFHZNEP has already been customized for an
installation using the IBM supplied sample program DFHZNEPX, copy
the relevant source code from XNCINEP2 into DFHZNEPX
and insert it before the trailing EXEC CICS RETURN call in
DFHZNEPX.