CICS Node Error Program Considerations for Natural - Natural CICS Interface Version 8.3

This Dokument discusses CICS node error program considerations.

The following topics are covered:

See also:

  • For information on installing a CICS node error program, refer to the corresponding section in Installing Natural CICS Interface for z/OS in the Natural Installation documentation.


Normal Situation

Whenever a Natural session is active, CICS resources such as thread storage, roll facility entries (that is, records in a VSAM RRDS file or in a CICS temporary storage queue), swap pool slots etc. are used.

If these resources are under the control of the Natural CICS Interface, they are correctly released whenever a session terminates normally or abnormally.

Situations Not under Control of Natural CICS Interface

The following cases cannot be controlled by the Natural CICS Interface:

  1. A non-Natural program called by Natural issues an EXEC CICS ABEND CANCEL command or the equivalent CICS macro request: the CICS task is canceled without the Natural CICS Interface receiving control to properly release all session resources.

  2. Some CICS monitor products offer tools to purge CICS tasks, bypassing any abnormal termination exit set by the application. If a Natural task is canceled this way, the Natural CICS Interface has no chance to release the resources still owned by the session.

  3. A user disconnects a terminal from the CICS region (by switching the power off or using an adequate session manager function) while a Natural session is currently not active in CICS (pseudo-conversational screen I/O).

Recovery Mechanisms

The Natural CICS Interface provides some recovery mechanisms to recover from such situations; for example:

Whenever a new Natural session is to be started, a table is scanned for another Natural session still active with the same terminal ID. If such a session exists, it is logically terminated, and all its resources are released prior to starting the new one.

However, it may take quite a long time between logically terminating the session and releasing its resources, and there may also be a security concern:

When the NTCICSP macro parameter COMARET is set to OFF, the information to resume a Natural session is kept in a CICS temporary storage record with the terminal ID being part of the temporary storage queue name. If another CICS user tries to start Natural with this terminal ID, he/she will resume the old Natural session rather than starting a new one.

The third case in the above list is the most crucial one. CICS provides a node error program (NEP) exit interface, which can be used in these cases to trigger the Natural CICS Interface to terminate the lost session. An appropriate module called NCIZNEP is provided in the Natural CICS Interface (see Natural CICS Sample Programs); it must be called by a DFHZNEP node error program.

Based on session restart information (NEXTTRANSID and restart data in COMMAREA or CICS temporary storage), the Natural CICS Interface tries to resume the session and terminate it logically.

NCIZNEP Functionality

Based on restart information (NEXTTRANSID and restart data in COMMAREA or CICS temporary storage) of a terminal bound session, which is currently pending in a pseudo-conversational screen I/O, NCIZNEP tries to resume the session asynchronously and terminate it logically.

Optionally, NCIZNEP can also try to purge an active Natural session. This functionality is available for CICS Transaction Server systems only. To enable this functionality, specify PURGE=YES for the NCIZNEP module link. See the installation procedure for the Natural CICS Interface and the section CICS Startup Parameters in Installing Natural CICS Interface for z/OS in the Natural Installation documentation.

MRO/CICSPlex environments:

  • The module NCIZNEP must be defined also in the AOR.

  • A transaction ID has to be defined for the module NCIZNEP in the AOR.

  • This transaction ID must also be set via the NEPTRAN parameter in the CICS startup parameters in the NCIZNEP module as described in Installing Natural CICS Interface for z/OS in the Natural Installation documentation.

Upon completion, NCIZNEP indicates to the caller (normally DFHZNEP), by clearing the parameter input, whether it has successfully completed its work; that is, launching the Natural session clean-up task.

This is in particular of interest, if more than one Natural CICS versions are active in a CICS system: clean-up function of a specific NCIZNEP may fail, because the Natural session to be tidied up is a different Natural CICS Interface version. DFHZNEP now can test whether the called NCIZNEP (for example, NCIvrNEP, where vr represents the current Natural version) was successful, and if not, call another NCIZNEP (for example, NCInnNEP, where nn may be any preceding Natural version).

Special Considerations

There are still some items to be considered:

  • The Natural CICS source library contains the sample node error program XNCINEP2 for CICS. This sample programs does not perform anything special for the Natural CICS environment, it merely calls (via LINK) the NCIZNEP module, which then deals with Natural under CICS.

  • DFHZNEP may already be customized for a specific installation; as only one node error program is possible, the logic of the relevant XNCINEPx program should be adapted to the existing DFHZNEP logic.

  • In MRO environments, DFHZNEP and NCIZNEP must be installed in the TOR.

  • The NCIZNEP module must be defined with EXECKEY(CICS).

  • In the case described under item 3. above, DFHZNEP may receive control more than once for various internal error codes, since each internal error code is related to a specific CICS error message, but there may be more than one error message resulting from a given action.

  • Upon completion NCIZNEP indicates to the caller (normally DFHZNEP) — by clearing the parameter input — if it has successfully completed its work, that is, launching the Natural session clean-up task.

  • The CICS control block constellation may have changed each time a node error program has been invoked, for example, the COMMAREA and NEXTTRANSID information in the TCTTE may have been lost after a certain node error event. In this case, the NTCICSP parameter COMARET must be set appropriately, which means that you cannot choose a node error event for your node error program to be invoked when passing the Natural pseudo-conversational session restart data in a CICS COMMAREA that has already been cleaned up by CICS.

Example Dummy Program

If you want to know how many times and with what error codes DFHZNEP is invoked on certain actions and how the TCTTE should look, write a dummy node error program, which only issues CICS trace requests showing the requested information.

The following sample enables a DFHZNEP error processor to receive control for all possible error codes passed to DFHZNEP:

     .
    
     DFHSNEP TYPE=INITIAL
    
     ORG NEPTT
    
     DC 256X'03' invoke error processor '3' for ALL error codes
    
     ORG ,
    
     DFHSNEP TYPE=ERRPROC,GROUP=3,CODE=49    
     .
     
     set up requested information and issue trace request(s)