This Natural profile parameter controls the initialization and operation
of the editor buffer pool and its work file. It corresponds to the
NTEDBP
macro in the Natural parameter module
NATPARM.
| Possible settings | See below | Various keywords subparameter are available. |
|---|---|---|
| Default setting | See below | |
| Dynamic specification | yes | This parameter can only be specified dynamically. In the Natural
parameter module NATPARM, the macro
NTEDBP
must be used instead.
|
| Specification within session | yes | Use the SYSEDT Editor Buffer Pool Administration
utility.
|
The editor buffer pool is defined for a session by profile parameter
BPI with
TYPE=EDIT or
by profile parameter EDPSIZE (editor auxiliary
buffer pool).
If the editor buffer pool is shared between multiple Natural sessions,
all subparameters (except DDNAME,
DSNAME and
FMODE) are
honored by the very first session only, which initializes the editor buffer
pool work file during a buffer pool cold start. During a buffer pool warm
start, the editor buffer pool subparameters (except
DDNAME, DSNAME and
FMODE) are read from the buffer pool work file.
With subparameter COLD=ON, a buffer
pool cold start can be forced during the initialization of the editor buffer
pool.
If an editor auxiliary buffer pool is used (see profile parameter
EDPSIZE), only
the following subparameters apply:
For more information on the editor buffer pool, refer to Editor Buffer Pool in the Operations documentation.
For more information on buffer pool performance, refer to the
SYSEDT
Editor Buffer Pool Administration utility documentation.
The following topics are covered below:
The EDBP parameter is specified as follows:
| EDBP=(keyword1=value1, keyword2=value2,...) |
The NTEDBP macro is specified as follows:
| NTEDBP keyword1=value1, keyword2=value2,... |
The following keyword subparameters are available:
COLD | CTOUT | DDNAME | DSNAME | DTOUT | FMODE | FTOUT | IMSG | ITOUT | LRECL | LTOUT | MAXLF | PWORK | RECNUM | RWORK | UTOUT
Determines whether a buffer pool cold start is performed.
| Possible values | ON or OFF |
| Default value | OFF |
A cold start means that the buffer pool work file is cleared and reinitialized during buffer pool initialization. Any editor recovery information and all buffer pool parameters stored in the work file are lost.
Determines the timeout value (in seconds) for changed buffer pool blocks.
| Possible values | 1-32767 |
| Default value | 120 |
A changed buffer pool block is written to the work file after the specified time interval has been exceeded, and no unchanged or free block is available.
Determines the logical work file name of the JCL definition.
| Possible values | 1 to 8 bytes |
| Default value | CMEDIT |
Notes:
SD file.
Determines the work file dataset name for batch and TSO under z/OS only.
| Possible values | 1-44 bytes |
| Default value | None |
If no DD JCL statement is supplied and no ALLOC statement
is issued (under TSO only) for the editor work file, then
DSNAME will be allocated dynamically.
Determines the logical file timeout check value (in seconds).
| Possible values | 1-32767 |
| Default value | 300 |
Logical files are checked for timeout each time the specified time interval has been exceeded.
Determines the file mode for the work file.
| Possible values | 1-2 characters |
| Default value | A1 |
Under VM/CMS, the specified value determines the file mode for the work
file. The file type is always DATA.
Under Com-plete/SMARTS, the value SM determines that a SMARTS work file
is used. In this case, the SMARTS environment variable
$NAT_WORK_ROOT determines the path.
Under Com-plete/SMARTS, if a value other than SM is specified, a Com-plete SD file is used.
In a SMARTS environment without Com-plete, SM must be specified.
Determines the timeout value (in seconds) for logical files.
| Possible values | 60-16777215 |
| Default value | 86400 |
A logical file is deleted after the specified time interval has been exceeded and no access has occurred.
Determines whether a buffer pool initialization and termination message is issued on the operator console.
| Possible values | ON or OFF |
| Default value | OFF |
Determines the buffer pool initialization timeout value (in seconds) for multi-user buffer pools only.
| Possible values | 1-32767 |
| Default value | 300 |
The buffer pool is initialized by the first user by whom it is accessed. Other users have to wait until the first user finishes initialization. If the initialization is not finished after the specified time interval (for example, due to an abnormal termination of the first user), all other users receive an error message.
Determines the buffer pool block size and work file record length.
This parameter is honored under BS2000/OSD, under Com-plete, under VM/CMS and for editor auxiliary buffer pools only.
For other environments, the work file record length is determined when the editor work file is created.
| Possible values | 800-16384 |
| Default value | 4096 |
Under BS2000/OSD, the record length must be a multiple of 2048 bytes.
Determines the timeout value (in seconds) for locked buffer pool blocks.
| Possible values | 1-32767 |
| Default value | 20 |
A buffer pool block that was locked during a read from the work file is freed after the specified time interval has been exceeded.
Determines the maximum number of logical files.
| Possible values | 100-999999 |
| Default value | 1000 |
Determines the percentage of work file records used as work records during an editor buffer pool cold start.
| Possible values | 0-100 |
| Default value | 50 |
The remaining records are used as recovery records.
Determines the number of work file records (under VM/CMS and Com-plete only) during an editor buffer pool cold start.
| Possible values | 100-65535 |
| Default value | 200 |
This number determines the size of the work file.
Note:
For environments other than CMS, the number of work file records is
determined when the editor work file is created.
Determines the percentage of work records that is used for regular logical files during an editor buffer pool cold start.
| Possible values | 51-100 |
| Default value | 90 |
The remaining records are used internally to release blocks from the buffer pool.
Determines the timeout value (in seconds) for unchanged buffer pool blocks.
| Possible values | 1-32767 |
| Default value | 20 |
An unchanged buffer pool block is written to the work file after the specified time interval has been exceeded and no free block is available.