Natural under TIAM Error Messages
This section lists the error messages (NRTnnnn messages) that may be
issued by the Natural TIAM teleprocessing interface.
Unlike Natural system messages, the explanatory long texts to these
messages and codes are only available in this document, not online.
NRTnnnn Messages
NRT0001 - NATURAL PARAMETER MODULE NOT FOUND
| Expl. |
Natural parameter module in front-end and reentrant part not
found.
|
NRT0002 - ERROR IN ENABLE CMP FOR BUFFER POOL MANAGER
| Expl. |
An error has occurred when trying to enable the memory pool
for the Natural buffer pool. The return code contains the SVC return code from
register 15.
|
NRT0003 - ERROR IN REQUEST CMP FOR BUFFER POOL MANAGER
| Expl. |
An error has occurred when trying to request the memory pool
for the Natural buffer pool. The return code contains the SVC return code from
register 15.
|
NRT0004 - ERROR IN ENABLE CMP FOR REENTRANT PART
| Expl. |
An error has occurred when trying to enable the memory pool
for the Natural load pool. The return code contains the SVC return code from
register 15.
|
NRT0005 - ERROR IN ENABLE CMP FOR GLOBAL BUFFER POOL
| Expl. |
An error has occurred when trying to enable the memory pool
for the global buffer pool. The return code contains the SVC return code from
register 15.
|
NRT0006 - ERROR IN LOAD OF REENTRANT PART OF Natural
| Expl. |
An error has occurred when trying to load the Natural
nucleus. The return code contains the SVC return code from register 15.
|
NRT0007 - ERROR IN ENABLE SERIALIZATION ITEM
| Expl. |
An error has occurred when trying to enable the serialization
item for the Natural start-up. The return code contains the SVC return code
from register 15.
|
NRT0008 - ERROR IN ENQUEUE ACCESS REQUEST
| Expl. |
An error has occurred when trying to enqueue the
serialization queue for the Natural session initialization.
|
NRT0009 - ERROR IN DEQUEUE ACCESS REQUEST
| Expl. |
An error has occurred when trying to dequeue the
serialization queue for the Natural session initialization.
|
NRT0010 - UNABLE TO ESTABLISH ADABAS COMMUNICATION
| Expl. |
The link module ADALNK or ADAUSER specified with the ADACOM
generation parameter is neither linked to the Natural front-end nor could it be
dynamically reloaded.
|
NRT0020 - SESSION TERMINATED DUE TO SEVERE ERROR(S)
| Expl. |
Session could not be initialized because resources were not
available.
|
NRT0021 - TERMINAL TYPE NOT SUPPORTED BY Natural
| Expl. |
The Natural session has been started from a terminal which is
not supported by Natural.
|
NRT0022 - ERROR DURING INITIALIZATION OF NAF CMP
| Expl. |
An error has occurred when trying to initialize the memory
pool for Natural Advanced Facilities. No reports can be output via NATSPOOL.
|
NRT0023 - NAF PARAMETER MODULE NOT LINKED IN
| Expl. |
The Natural Advanced Facilities parameter module could not be
located.
|
NRT0025 - MODULE NATINV NOT LINKED FIRST TO NUCLEUS
| Expl. |
The NATINV module was not included as the first one when
linking the Natural nucleus.
|
NRT0026 - MODULE NATLAST NOT LINKED TO THE NUCLEUS
| Expl. |
The NATLAST module was not included in the link of the
Natural nucleus. NATLAST must be included as the last module.
|
NRT0027 - LINK ERROR FOR ADDRESS: nnnnnnnn
| Expl. |
The module "nnnnnnnn" specified in
LINK or LINK2 of the NATTIAM generation parameters could not be located. The
module was probably not linked to the Natural TIAM front-end.
|
NRT0030 - ERROR DURING READ OF DYNAMIC PARAMETER FILE
| Expl. |
Read of dynamic parameter file failed. |
NRT0031 - ERROR DURING OPEN OF DYNAMIC PARAMETER FILE
| Expl. |
DMS error occurred during opening of parameter file. |
NRT0032 - REENTRANT PART OF TIAM DRIVER NOT FOUND
| Expl. |
Reentrant part of TIAM driver found neither in the reentrant
nor in the front-end part.
|
NRT0040 - FRONT-END REENTRANT PART EXHIBIT A DIFFERENT ADDRESS
MODE
| Expl. |
The value (either 24 or 31) specified for the PARMOD
parameter for the Natural reentrant part does not correspond to the one
specified for the front-end part.
|
