EDT0000 | EDT0001 | EDT0002 | EDT0003 | EDT0004 | EDT0005 | EDT0006 | EDT0007 | EDT0008 | EDT0009 | EDT0010 | EDT0011 | EDT0012 | EDT0013 | EDT0014 | EDT0015 | EDT0016 | EDT0017 | EDT0018 | EDT0020 | EDT0021 | EDT0022 | EDT0023 | EDT0024 | EDT0025 | EDT0026 | EDT0027 | EDT0028 | EDT0029 | EDT0030 | EDT0031 | EDT0032 | EDT0033 | EDT0034 | EDT0035 | EDT0036 | EDT0037 | EDT0038 | EDT0039 | EDT0040 | EDT0041 | EDT0042 | EDT0045 | EDT0047 | EDT0050 | EDT0051 | EDT0052 | EDT0053 | EDT0054 | EDT0055 | EDT0056 | EDT0057 | EDT0058 | EDT0059 | EDT0060 | EDT0061 | EDT0062 | EDT0063 | EDT0064 | EDT0065| EDT0000 | Work file size too large |
| Explanation: |
An attempt was made to create a work file. The number of blocks requested was calculated to exceed 100 tracks. |
| System action: |
The request is ignored and processing continues. |
| Terminal operator info: |
A smaller size (fewer blocks) should be requested. |
| EDT0001 | Profile Processor Error |
| Explanation: |
Self-explanatory message. |
| EDT0002 | Statement Handler Error |
| Explanation: |
Self-explanatory message. |
| EDT0003 | Illegal Fetch |
| Explanation: |
Self-explanatory message. |
| EDT0004 | Invalid Tabs Specified |
| Explanation: |
Self-explanatory message. |
| EDT0005 | Security Violation |
| Explanation: |
Self-explanatory message. |
| EDT0006 | Unable To Load Module UETABS |
| Explanation: |
Self-explanatory message. |
| EDT0007 | Unrecognised Response |
| Explanation: |
Self-explanatory message. |
| EDT0008 | SD file is in use |
| Explanation: |
This message is associated with a function that uses an SD file. When Com-plete attempted to open the user's SD file, it was found to be in use. |
| System action: |
No action takes place. |
| Terminal operator info: |
Terminate any other edit functions that might be using the same SD file. If this does not solve the problem, contact your system programmer. |
| EDT0009 | Record length error |
| Explanation: |
A member of a PDS of a length less than 80 or more than 255 bytes is being edited. |
| System action: |
None. |
| Terminal operator info: |
Correct the length of the data set and retry. |
| EDT0010 | No SD file to recover |
| Explanation: |
The user attempted to recover a lost edit session and the SD file could not be found by the system. |
| System action: |
None. |
| Terminal operator info: |
None. |
| EDT0011 | Access denied |
| Explanation: |
A user exit has denied access to the data set. |
| System action: |
None. |
| Terminal operator info: |
None. |
| EDT0012 | Aborted by userexit |
| Explanation: |
A user exit has caused the requested operation to be aborted. |
| System action: |
None. |
| Terminal operator info: |
None. |
| EDT0013 | PANSEQ DDcard missing |
| Explanation: |
The PANSEQ DDCARD is missing from the Com-plete startup JCL. The PANVALET interface will not function without it. |
| System action: |
None. |
| Terminal operator info: |
Contact the system programmer. |
| EDT0014 | LIBSEQ DDcard missing |
| Explanation: |
The LIBSEQ DDCARD is missing the Com-plete JCL. The librarian interface will not function without it. |
| System action: |
None. |
| Terminal operator info: |
Contact the system programmer. |
| EDT0015 | DDcard missing |
| Explanation: |
The DDCARD for the library being edited through PANVALET or LIBRARIAN access routines is missing. |
| System action: |
None. |
| Terminal operator info: |
Contact the system programmer. |
| EDT0016 | Member empty |
| Explanation: |
An empty PDS member is being edited. |
| System action: |
None. |
| Terminal operator info: |
None. |
| EDT0017 | LIBRARIAN error, Rc=X'$1' |
| Explanation: |
There is an error in the LIBRARIAN ACCESS module. |
| System action: |
None. |
| Terminal operator info: |
Contact the system programmer. |
| EDT0018 | BLDL error |
| Explanation: |
A probable hardware error has occurred while building BLDL information. |
| System action: |
None. |
| Terminal operator info: |
Inform the system programmer. |
| EDT0020 | Sequence error |
| Explanation: |
A sequencing error has occurred in the specified volume. |
| System action: |
None. |
| Terminal operator info: |
Correct the sequence number specified. |
| EDT0021 | Unsupported language |
| Explanation: |
An unsupported language type has been specified for SET TABS. |
| System action: |
None. |
| Terminal operator info: |
TAB settings are supported for ASSEMBLER, PL/I, COBOL and FORTRAN. |
| EDT0022 | PANVALET not available |
| Explanation: |
The user attempted to edit a PANVALET-controlled member and the PANVALET interface is not installed. |
| System action: |
None. |
| Terminal operator info: |
Contact the system programmer to install the interface. |
| EDT0023 | Library busy, please wait |
| Explanation: |
Another user has the library enqueued, probably to do a save. |
| System action: |
None. |
| Terminal operator info: |
Try again a little later. |
| EDT0024 | Library is read-only |
| Explanation: |
Library has been defined as read-only to security exits and an update operation has been attempted. |
| System action: |
None. |
| Terminal operator info: |
None. |
| EDT0025 | Library not defined |
| Explanation: |
A two-character library access code was used and could not be matched with a data set name in the UEDTB1 or ULIBID tables. |
| System action: |
None. |
| Terminal operator info: |
Use a correct two-character code or the full data set name. |
| EDT0026 | DSORG/Space invalid |
| Explanation: |
The file being edited is not a PDS member or a sequential file. Or the record length of the file is bigger than 255. Only fix(block)ed datasets are supported. |
| System action: |
None. |
| Terminal operator info: |
None. |
| EDT0027 | Not enough storage |
| Explanation: |
This message is associated with the READ, RECOVER, or INSERT commands and indicates that there is insufficient storage for an SD file to be opened. |
| System action: |
None. |
| Terminal operator info: |
Contact the system programmer to recatalog UEDIT with a larger region size. |
| EDT0028 | I/O error on library |
| Explanation: |
Probable hardware error. |
| System action: |
None. |
| Terminal operator info: |
Inform the system programmer. |
| EDT0029 | Library not found |
| Explanation: |
The library accessed by the data set name entered cannot be located in the catalog or specified volume. |
| System action: |
None. |
| Terminal operator info: |
Use the correct data set name and retry. |
| EDT0030 | Aborted by the user |
| Explanation: |
An edit session was terminated by the user, usually by pressing the CLEAR key. |
| System action: |
The edit file is available for later recovery. |
| Terminal operator info: |
If desired, use the RECOVER function from the Full Screen Editor menu to recover the aborted session. |
| EDT0031 | Library/DSN access error |
| Explanation: |
An unexpected error occurred while accessing a library. |
| System action: |
The command is ignored. |
| Terminal operator info: |
If the error persists, contact your Com-plete system programmer. |
| System programmer info: |
Contact Com-plete support. |
| EDT0032 | Library full |
| Explanation: |
An attempt to save a member into a data set was made and, because the library was full, the operation failed. |
| System action: |
The command is ignored and processing continues. The edit file is available for later recovery. |
| Terminal operator info: |
Have the library compressed or reallocated. |
| EDT0033 | PANVALET error, Rc=X'$1' |
| Explanation: |
A non-zero return code was received from the PANVALET program product for the operation attempted. |
| System action: |
The command is ignored and processing continues. |
| Terminal operator info: |
Determine the cause of the error, correct it, and retry the operation. |
| EDT0034 | Directory full |
| Explanation: |
An attempt was made to save a member into a PDS and the directory was full. |
| System action: |
The command is ignored and processing continues. The SD edit file is available for recovery at a later time. |
| Terminal operator info: |
The data set should be compressed or reallocated with additional directory blocks. |
| EDT0035 | Member not found |
| Explanation: |
The member name specified was not found in the library searches. |
| System action: |
The command is ignored and processing continues. |
| Terminal operator info: |
Specify a valid member name for the library specified. |
| EDT0036 | Member already exists |
| Explanation: |
An attempt to create an already existing member was attempted. |
| System action: |
The command is ignored and processing continues. |
| Terminal operator info: |
Either use the EDIT function to edit the existing member, or the CREATE function to create a member that does not already exist. |
| EDT0037 | No member specified |
| Explanation: |
An edit session was attempted without a member name being given. |
| System action: |
The request is ignored and processing continues. |
| Terminal operator info: |
Specify a valid member name. |
| EDT0038 | Number of records in file exceeds the maximum SDfile size |
| Explanation: |
The number of records in the file plus SDSIZE/4 exceeds 32760, the maximum number of records UEDIT can save into it's SDfile. |
| System programmer info: |
Lower Sysparm SDSIZE or use another Editor (e.g. TSO) to work on such big files. |
| Appl. programmer info: |
Use another Editor (e.g. TSO) to work on such big files. |
| EDT0039 | Read aborted by PC |
| Explanation: |
The escape sequence for NATURAL CONNECTION was entered during the READ attempt (upload). |
| System action: |
The command is ignored and processing continues. |
| Terminal operator info: |
None. |
| EDT0040 | Save aborted by PC |
| Explanation: |
The escape sequence for NATURAL CONNECTION was entered during the SAVE attempt (download). |
| System action: |
The command is ignored and processing continues. |
| Terminal operator info: |
None. |
| EDT0041 | 0 records read |
| Explanation: |
A READ operation (upload) was performed and the member was found to contain zero records. |
| System action: |
Processing continues normally. |
| Terminal operator info: |
None. |
| EDT0042 | PC I/O error |
| Explanation: |
A physical I/O error has occurred during an upload or download request. |
| System action: |
The upload or download is aborted. |
| Terminal operator info: |
Retry the upload or download operation. |
| EDT0045 | DSN/Library access error |
| Explanation: |
Self-explanatory message. |
| EDT0047 | Invalid record format on upload |
| Explanation: |
Self-explanatory message. |
| EDT0050 | Please enter a valid new name |
| Explanation: |
Self-explanatory message. |
| EDT0051 | Please enter a valid member name |
| Explanation: |
Self-explanatory message. |
| EDT0052 | Please Enter Libid Or DSN |
| Explanation: |
Self-explanatory message. |
| EDT0053 | Please enter Volume Serial No. |
| Explanation: |
Self-explanatory message. |
| EDT0054 | Please Enter Function |
| Explanation: |
Self-explanatory message. |
| EDT0055 | Please Enter Profile Name |
| Explanation: |
Self-explanatory message. |
| EDT0056 | Please Enter Profile Name |
| Explanation: |
Self-explanatory message. |
| EDT0057 | Profile Library Not Defined in system |
| Explanation: |
Self-explanatory message. |
| EDT0058 | Rename Aborted, Newsub Blank |
| Explanation: |
Self-explanatory message. |
| EDT0059 | Rename Aborted, Newtyp Blank |
| Explanation: |
Self-explanatory message. |
| EDT0060 | Member already exists |
| Explanation: |
Self-explanatory message. |
| EDT0061 | Conflicting Level Info |
| Explanation: |
Self-explanatory message. |
| EDT0062 | Invalid Level Number |
| Explanation: |
Self-explanatory message. |
| EDT0063 | Invalid Date |
| Explanation: |
Self-explanatory message. |
| EDT0064 | Invalid Time |
| Explanation: |
Self-explanatory message. |
| EDT0065 | Too many records in input data set |
| Explanation: |
The input data set has more than 32760 records. |