ARSX02 | ARSX03 | ARSX04 | ARSX05 | ARSX09 | ARSX10 | ARSX13 | ARSX14 | ARSX97 | ARSX98 | ARSX99
ARSX02 | dbid LOAD FAILED FOR MODULE module |
Explanation |
The specified module cannot be loaded. |
Action |
The requested load module might be missing. |
ARSX03 | dbid REVIEW HUB ID= target-id LOG RSP nnn SUB nnn. |
Explanation |
A response code nnn (ADARSPnnn) subcode nnn was received while sending a LOG record to the Adabas Review hub. |
Action |
Refer to the Adabas Messages and Codes guide. |
ARSX04 | dbid REVIEW HUB ID= target_id is not active. dbid REVIEW parameter set to NO. |
Explanation |
A response code 148 (ADARSP148) was received on a request call to the Adabas Review hub. |
Action |
Start the appropriate Adabas Review hub. |
ARSX05 | dbid UEX5: Requested wait for nnnnn seconds. dbid UEX5: Invalid REQ (xx ), IGNORE assumed. |
Explanation |
On any error condition, ADARSX calls user exit 5 if present. User exit 5 may return one of three possible service requests:
The message displays the number of seconds delay time returned from the user exit 5. If an unknown request is received from the user exit, the request is ignored, and processing continues. |
Action |
No action required for the first message. The INVALID REQ message indicates a problem with the user exit 5. Correct the problem and restart the Adabas nucleus, when possible. |
ARSX09 | dbid Subtask ADARSX detached. |
Explanation |
The subtask ADARSX was detached for one of the following reasons:
If the subtask is not attached, this database does not send data to the Adabas Review hub. |
Action |
If the reason for the detachment is an unjustified Adabas response code 148 (ADARSP148), contact your Software AG technical support representative. |
ARSX10 | dbid Unrecoverable abend in subtask ADARSX. |
Explanation |
The subtask ADARSX abended either due to an unrecoverable abend or to the second call of the ESTAE (in this case see previous ARSXxx messages). The subtask is deactivated, and the database will not send data to the Adabas Review hub. |
Action |
It is not possible to reactivate the subtask using the ADARUN REVIEW=hubid parameter. You must restart the database to reactivate Adabas Review. |
ARSX13 | ARSX13 XXXXX Internal error. |
Explanation |
An internal error occurred. Examine the messages displayed by the operating system and correct the problem. A necessary module might not be in the library concatenations so it could not be found to be loaded. |
Action |
Contact your Software AG technical support representative. |
ARSX14 | XXXXX REVIEW parameter set to NO. |
Explanation |
Review has been disabled due to an error. A preceding message will identify the specific error. |
Action |
Correct the issue and restart the Adabas nucleus. |
ARSX97 | dbid Receiving Data Configuration dbid Buffer pool length in MB: dbid Delay time in seconds: |
Explanation |
At initialization of subtask ADARSX, the following information is reported.
|
Action |
No action is required for this informational message. |
ARSX98 | dbid Sending Data Configuration dbid Buffer length in MB: dbid Max number CLOGs per buffer: |
Explanation |
At initialization of subtask ADARSX, the following information is reported.
|
Action |
No action is required for this informational message. |
ARSX99 | dbid REVIEW HUB send bulk subtask is initializing: dbid ADARSX built V vrs YYYY-MM-DD HH:MM |
Action |
No action is required for this informational message. |