These messages are written to the operator console and to SYSLST by the optional Adabas job exit. See the Adabas Installation documentation for more information.
SAGI001 | SAGI005 | SAGI006 | SAGI010 | SAGI016 | SAGI091 | SAGI092 | SAGI093 | SAGI095 | SAGI096 | SAGI097 | SAGI098 | SAGI099 | SAGI101 | SAGI102| SAGI001 | Software AG job exit Vv installed |
| Explanation |
The Software AG job control exit is active. |
| Action |
SAGUSER control statements will be processed. |
| SAGI005 | Table allocated (low) ADDR=addr |
| Explanation |
The SAGUSER table was allocated in system GETVIS below the 16-MB line at the address indicated. |
| SAGI006 | Table allocated (high) ADDR=addr |
| Explanation |
The SAGUSER table was allocated in system GETVIS above the 16-MB line at the address indicated. |
| SAGI010 | Software AG job exit already installed |
| Explanation |
The Software AG job control exit can be installed only once. |
| Action |
No action is required if the Software AG job exit is actually installed. If it is not, perform an IPL and reestablish the job control exit chain. |
| SAGI016 | Table already allocated ADDR=addr |
| Explanation |
The program SAGINST has already allocated the DD name table. |
| Action: |
No action is required if the Software AG job exit is actually installed. If it is not, perform an IPL and reestablish the job control exit chain. |
| SAGI091 | Unable to locate $JOBEXIT in SDL |
| Explanation |
The entry for phase $JOBEXIT was not found in the SDL. The Software AG job exit cannot be installed. |
| Action: |
Get information on the version, release, and service pack number of the operating system and call Software AG for support. |
| SAGI092 | Unable to locate SAGJBXT in SDL |
| Explanation |
The entry for phase SAGJBXT was not found in the SDL. The Software AG job exit cannot be installed. |
| Action |
Verify that phase SAGJBXT was loaded into the SVA. |
| SAGI093 | Phase SAGJBXT in error |
| Explanation |
The phase SAGJBXT loaded into the SVA is not the job control exit supplied by Software AG. The Software AG job exit cannot be installed. |
| Action |
Verify a probable error during the linkage edit of SAGJBXT. |
| SAGI095 | Unable to determine VSE level |
| Explanation |
Information about z/VSE (i.e., version and release) could not be found in the supervisor. The Software AG job exit cannot be installed. A storage dump is produced. |
| Action |
Obtain the z/VSE version and release level; call Software AG for support. |
| SAGI096 | SAGJBXT ID not found in $JOBEXIT table |
| Explanation |
An entry for SAGJBXT was not found in the $JOBEXIT table (for z/VSE 1.2 and above). The Software AG job exit cannot be installed. |
| Action: |
Add an entry for SAGJBXT in $JOBEXIT and retry the program SAGINST. |
| SAGI097 | SAGJBXT phase phase not found |
| Explanation |
The phase for SAGJBXT was found in the $JOBEXIT table (for z/VSE 1.2 and above), but the phase has not been loaded into the SVA. The Software AG job exit cannot be installed. |
| Action |
Verify that phase SAGJBXT was loaded into the SVA. |
| SAGI098 | SAGJBXT phase phase not in SVA |
| Explanation |
The phase for SAGJBXT was found in the $JOBEXIT table (for z/VSE 1.2 and above) and has been loaded, but not into the SVA. The Software AG job exit cannot be installed. |
| Action: |
Verify that phase SAGJBXT was loaded into the SVA. |
| SAGI099 | SAGJBXT phase phase not valid |
| Explanation |
The phase for SAGJBXT was found in the $JOBEXIT table (for z/VSE 1.2 and above) and has been loaded, but not into the SVA. The Software AG job exit cannot be installed. |
| Action: |
Verify that phase SAGJBXT was loaded into the SVA. |
| SAGI101 | Allocation error (high) RC=ret-code |
| Explanation |
An attempt to allocate space for the DD name table in 31-bit mode failed. The return code is from the GETVIS macro. The Software AG job exit will not process SAGUSER statements. |
| Action: |
Verify that enough storage is available in the SVA for the DD name table; then rerun SAGINST. |
| SAGI102 | Allocation error (low) RC=ret-code |
| Explanation |
An attempt to allocate space for the DD name table in 24-bit mode failed. The return code is from the GETVIS macro. The Software AG job exit will not process SAGUSER statements. |
| Action: |
Verify that enough storage is available in the SVA for the DD name table; then rerun SAGINST. |