Version 8.2.2

Installing Adabas Transaction Manager for z/VSE


The Installation Medium

Review the Software AG Product Delivery Report that accompanies the release package before restoring the release data to disk.

The installation medium contains the following datasets in the sequence indicated in the report:

Data Set Contents
ATMvrs.LIBR Executable modules and sample jobs
ATMvrs.INPL Online Services application
ATMvrs.ERRN Online Services messages

where vrs is the version, revision, and system maintenance level of the product. Use the comments in the jobs when modifying them to conform to site requirements.

Top of page

Installation Checklist

The Adabas System Coordinator must be installed prior to the installation of Adabas Transaction Manager. See the Adabas System Coordinator documentation for detailed information.

Once the required System Coordinator components have been installed, you can proceed to install Adabas Transaction Manager. The following checklist identifies the steps necessary to complete the installation:

Step Description
1 Restore the Adabas Transaction Manager libraries from the installation medium
2 Prepare SYSATM
3 Enable the client process
4 Enable the database process for two-phase commit
5 Prepare the recovery file
6 Enable the Transaction Manager to run as a Service within Adabas System Coordinator daemons
7 Verify the installation

Top of page

Installation Procedure

Following is the general Adabas Transaction Manager installation procedure. The actual installation depends on your particular requirements and the specific contents of the release package provided by Software AG for your site. Information in the release package is intended for your system. If that information differs from the information in this section, use the release package information or contact Software AG technical support for assistance.

Step 1: Restore the Adabas Transaction Manager Libraries

Use the following sample JCS to restore the Adabas Transaction Manager library. Modify the following variables to reflect the standards at your site:

Variable Is the...
cuu medium unit number
vrs version, revision, and system maintenance level
tttttt volume serial number of the installation medium
xx file spacing information; see the Software AG Product Delivery Report
* $$ JOB JNM=LIBREST,CLASS=O,DISP=D
* $$ LST CLASS=A,DISP=H
// JOB LIBREST
// ASSGN SYS006,cuu,VOL=tttttt
// ASSGN SYS005,IGN
// MTC REW,SYS006
// MTC FSF,SYS006,xx
// EXEC LIBR
RESTORE S=SAGLIB.AVIvrs:SAGLIB.AVIvrs               -
TAPE=SYS006 TL=tttttt LIST=Y
/*
// MTC REW,SYS006
/&
* $$ EOJ

Step 2: Prepare SYSATM

The Adabas Transaction Manager Online Services (SYSATM) objects are delivered on the Adabas Transaction Manager distribution medium.

Start of instruction setTo prepare SYSATM:

  1. Use your everyday Natural INPL job to load the administration tool (Natural application SYSATM) and associated message texts into your Natural system. For reference a sample Natural INPL job called CORI061 can be found with the sibling System Coordinator product in the jobs distribution file. The INPL job’s work file 1 must reference the distribution file ATMvrs.INPL and work file 2 must reference ATMvrs.ERRN.

    Note:
    If you use Natural Security in this system, define the libraries SYSATM and SYSMTvrs (where vrs is the level you are installing) and protect as you require. You may define MENU as the startup transaction for SYSATM. However, you must not define a startup transaction for SYSMTvrs.

  2. Use the following parameter to define the Natural session where SYSATM is to be used:

    LFILE=(152,dbid,fnr<,passw><,ciph>) 

    where dbid and fnr define the location of the Adabas System Coordinator configuration file.

    Alternatively, assemble the Natural parameter module with

    NTFILE,ID=152,DBID=dbid,FNR=fnr 

Step 3: Enable the Client Process

Start of instruction setTo enable the Adabas Transaction Manager client process:

  1. For the Adabas System Coordinator:

  2. For Adabas Transaction Manager:

  3. For each Client:

Step 4: Enable the Database Process for Two-Phase Commit

Start of instruction setTo enable the Adabas Transaction Manager database process for two-phase commit:

  1. For the Adabas System Coordinator:

  2. For Adabas Transaction Manager:

Note:
An unmodified ADALNK must be available to the database in preference to the ADALNK created during the installation of the Adabas System Coordinator.

Step 5: Prepare the recovery file

All recovery information is maintained in a single direct access file defined to the Adabas System Coordinator daemon where the transaction manager service runs. The recovery file is shared by all transaction managers operating in the same Adabas System Coordinator group. For reference a sample formatting job called CORI040 can be found with the sibling System Coordinator product in the jobs distribution file. Change the parameters in this sample job with the following considerations:

"dsname" (file name)

Specify the file name, for example SAG.ATMvrs.cor-group-name.TMRFI

"nn" (file size in cylinders) and "@@@@" (device type)

The minimum block size of the file must be 4096 bytes, and we recommend a minimum size of 13,500 blocks for each transaction manager sharing the file. With reference to the Adabas Device Types and Block sizes section of the DBA Reference Summary, calculate how many cylinders are required for this many blocks based on the device type(s) available at your site. For example, when formatting a file assigned as a WORK component (as defined in the sample job), 13,500 blocks equates to 100 cylinders (nn) when using a 3390 device type ("@@@@").

Note:
It is very important that all transaction managers operating within the same Adabas System Coordinator group share the same recovery file.

Step 6: Enable the Transaction Manager to run as a Service within Adabas System Coordinator Daemons

Start of instruction setTo enable the Transaction Manager to run as a service within Adabas System Coordinator daemons:

  1. set PRODUCT=ATM in the parameter input of each System Coordinator daemon within which you wish to run the Transaction Manager.

  2. ensure the TM controls are correctly defined for each System Coordinator daemon within which you wish to run the Transaction Manager. Refer to How to maintain TM controls.

  3. Make the Adabas Transaction Manager load library available.

  4. refer to the section Prerequisites...Adabas System Coordinator for information on the System Coordinator daemon dataset definitions necessary for the correct operation of the Transaction Manager.

Note:
An Adabas Transaction Manager must be run in each operating system image that will participate in distributed transaction processing (DTP). If more than one Adabas SVC is used in the same system image, an Adabas Transaction Manager must be run under each Adabas SVC that will participate in DTP.

Step 7: Verify the Installation

Use the procedure described in section Verifying the Installation to ensure that the installation has been successful.

Top of page