ERROR-121 | ERROR-122 | ERROR-123 | ERROR-124 | ERROR-125 | ERROR-126 | ERROR-127 | ERROR-128 | ERROR-129 | ERROR-130 | ERROR-131 | ERROR-132 | ERROR-133 | ERROR-134| ERROR-121 | Parameter PRINT must be set to DUMP, FORMAT or BOTH |
| Explanation |
An invalid value was specified for the ADARPP PRINT parameter. Valid values are listed in the message. |
| Action |
Correct the value and try again. |
| ERROR-122 | Date and time must be reasonable. Date must be entered in the form YYYYMMDD. Time must be entered in the form HHMMSSTH. |
| Explanation |
An invalid value was specified for a date or time parameter in an ADARPP run. The date must be later that 1982 and the time value must be less than 24 hours. |
| Action |
Correct the relevant date or time parameter and try again. |
| ERROR-123 | Parameter STATE must be set to YES, or NO. |
| Explanation |
An invalid value was specified for the ADARPP STATE parameter. Valid values are listed in the message. |
| Action |
Correct the value and try again. |
| ERROR-124 | Print level must be in the range 0 to n inclusive for parameter |
| Explanation |
The print level specified for the ADARPP parameter identified in the message is invalid. |
| Action |
Review the valid settings for the named print parameter, correct the value, and try again. |
| ERROR-125 | Record number nnn: URBLTYPE: aa is not supported. Consult Software Support. |
| Explanation |
The record contains an unknown record type value. |
| Action |
Contact your Software AG technical support representative. |
| ERROR-126 | FROMDATE and FROMTIME must be <= to TODATE and TOTIME |
| Explanation |
The date and time specified by the ADARPP FROMDATE or FROMTIME parameters is later than the date and time specified by the TODATE and TOTIME parameters. This is invalid. |
| Action |
Correct the appropriate date or time value and try again. |
| ERROR-127 | Parameter TIMEZONE must be set to MACHINE, LOCAL, or an integer value in the range -23 to +23. When entering + or -, enclose the number in single quotes. |
| Explanation |
An invalid value was specified for the ADARPP TIMEZONE parameter. Valid values are listed in the message. |
| Action |
Correct the value and try again. |
| ERROR-128 | Record number nnn: URBLPTYP nn is inconsistent with eye-catcher aaaa, Consult Software Support. |
| Explanation |
The record contains a data type that is not consistent with the actual data. |
| Action |
Contact your Software AG technical support representative. |
| ERROR-129 | Record number nnn: URBLPTYP nn is not supported. Consult Software Support. |
| Explanation |
The record contains an unknown data type value. |
| Action |
Contact your Software AG technical support representative. |
| ERROR-130 | Failure on writing to print file. Consult Software Support. |
| Explanation |
An error occurred when a record was being written to the Report file. |
| Action |
Contact your Software AG technical support representative. |
| ERROR-131 | Open failed for file DDCLOG with returned code of nn. |
| Explanation |
No DDCLOG file was specified in the ADARPP JCL. |
| Action |
Correct the JCL and rerun the job. |
| ERROR-132 | Invalid parameters supplied. |
| Explanation |
At least one parameter value was invalid. |
| Action |
Check all error messages to identify the invalid parameter values, make corrections to the values, and try again. |
| ERROR-133 | nnnn CLOG records were read, and nnnn records were selected for printing. |
| Explanation |
A summary of the CLOG records read and selected for printing is listed in the message. This is part of the summary report at the end of the print file. |
| Action |
No action is necessary for this informational message. |
| ERROR-134 | PAGESIZE must be 20 or greater |
| Explanation |
An invalid value was specified for the ADARPP PAGESIZE parameter. Valid values must range from 20 or greater. |
| Action |
Correct the value and try again. |
