Compression/Decompression Error Messages
This section lists the error messages
(NUS02nn) that may be issued by the Natural thread
compression routine as a result of internal errors.
NUS0201 - INVALID OP.CODE OR FIRST ENTRY IS NOT THE COMPRESSION
BUFFER
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0202 - NUMBER OF TABLE ELEMENTS IS ZERO
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0203 - NUMBER OF TABLE ELEMENTS IS GREATER MAX.
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0204 - TOTAL THREAD LENGTH LOWER COMPRESSED
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0205 - BUFFER TYPE MISSING
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0206 - COMPRESSED BUFFER GREATER TOTAL LENGTH
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0207 - TOTAL LENGTH GREATER UPPER LIMIT
| Explanation |
The Natural user thread is too small. |
| Action |
Enlarge the Natural user thread. |
NUS0208 - INCORRECT TOTAL BUFFER LENGTH
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0209 - INCORRECT USED BUFFER LENGTH
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0210 - THREAD TOO SMALL FOR DECOMPRESSION
| Explanation |
The Natural user thread is too small. |
| Action |
Enlarge the Natural user thread. |
NUS0211 - BUFFER OFFSET/ADDRESS NOT POSITIVE
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0212 - ERROR IN BUFFER SORT SEQUENCE
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0213 - INCORRECT BUFFER OVERLAPPING
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0214 - TOTAL OR USED BUFFER LENGTH IS INVALID
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0215 - INVALID THREAD STATUS FOR OPERATION
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0216 - INVALID BUFFER LENGTH IN PREFIX
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0217 - INVALID LENGTH LOW END IN PREFIX
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0218 - INVALID LENGTH HIGH END IN PREFIX
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0219 - INVALID LENGTH BEFORE COMPR. BUFFER
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0220 - CMCCBR CALLED WITH COMPRESSED THREAD
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0221 - CMCCBR THREAD STATUS IS UNDEFINED
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0222 - INVALID BUFFER ID OR EYE CATCHER DESTROYED
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0223 - ERROR FROM CMFREMP FOR OUTSIDE BUFFER
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0224 - PHYS.GETMAIN ERROR FOR A FIXED BUFFER BELOW
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0225 - PHYS.GETMAIN ERROR FOR A VAR.BUFFER BELOW
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0226 - FREE MAIN FOR WORKPOOLS NOT DONE
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
NUS0227 - STORAGE OVERFLOW - yyy
BYTES GREATER zzz
|
yyy
|
represents the number of bytes which exceed the value
defined by the keyword parameters OVSIZE or
WPSIZE.
|
| zzz
|
represents the value defined for the operand of the
keyword parameters OVSIZE or
WPSIZE of the macro NTPRM.
|
| Explanation |
During a physical GETMAIN, one of the maximum sizes defined
in the keyword parameters OVSIZE or
WPSIZE in the macro NTPRM is exceeded.
|
| Action |
Increase the maximum size of
OVSIZE or WPSIZE of the macro
NTPRM.
|
NUS0228 - GETMAIN FOR BIT TABLE BUFFER FAILED
| Explanation |
Internal error. |
| Action |
Send the corresponding dump to Software AG Support.
|
