Compression/Decompression Error Messages
This section lists the error messages
(NUS02nn) that may be issued by the Natural thread
compression routine as a result of internal errors.
NUS0201 - INVALID OP.CODE OR FIRST ENTRY IS NOT THE COMPRESSION
BUFFER
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0202 - NUMBER OF TABLE ELEMENTS IS ZERO
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0203 - NUMBER OF TABLE ELEMENTS IS GREATER MAX.
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0204 - TOTAL THREAD LENGTH LOWER COMPRESSED
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0205 - BUFFER TYPE MISSING
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0206 - COMPRESSED BUFFER GREATER TOTAL LENGTH
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0207 - TOTAL LENGTH GREATER UPPER LIMIT
Explanation |
The Natural user thread is too small. |
Action |
Enlarge the Natural user thread (under openUTM,
change operand of parameter MAXSIZE in macro
NTSWPRM ).
|
NUS0208 - INCORRECT TOTAL BUFFER LENGTH
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0209 - INCORRECT USED BUFFER LENGTH
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0210 - THREAD TOO SMALL FOR DECOMPRESSION
Explanation |
The Natural user thread is too small. |
Action |
Enlarge the Natural user thread (under openUTM,
change operand of parameter MAXSIZE in macro
NTSWPRM ).
|
NUS0211 - BUFFER OFFSET/ADDRESS NOT POSITIVE
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0212 - ERROR IN BUFFER SORT SEQUENCE
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0213 - INCORRECT BUFFER OVERLAPPING
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0214 - TOTAL OR USED BUFFER LENGTH IS INVALID
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0215 - INVALID THREAD STATUS FOR OPERATION
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0216 - INVALID BUFFER LENGTH IN PREFIX
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0217 - INVALID LENGTH LOW END IN PREFIX
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0218 - INVALID LENGTH HIGH END IN PREFIX
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0219 - INVALID LENGTH BEFORE COMPR. BUFFER
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0220 - CMCCBR CALLED WITH COMPRESSED THREAD
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0221 - CMCCBR THREAD STATUS IS UNDEFINED
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0222 - INVALID BUFFER ID OR EYE CATCHER DESTROYED
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0223 - ERROR FROM CMFREMP FOR OUTSIDE BUFFER
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0224 - PHYS.GETMAIN ERROR FOR A FIXED BUFFER BELOW
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0225 - PHYS.GETMAIN ERROR FOR A VAR.BUFFER BELOW
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0226 - FREE MAIN FOR WORKPOOLS NOT DONE
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |
NUS0227 - STORAGE OVERFLOW - yyy BYTES
GREATER zzz
yyy
|
represents the number of bytes which exceed the value defined
by the keyword parameters OVSIZE or
WPSIZE .
|
zzz
|
represents the value defined for the operand of the keyword
parameters OVSIZE or WPSIZE of
the macro NTPRM .
|
Explanation |
During a physical GETMAIN , one of
the maximum sizes defined in the keyword parameters
OVSIZE or WPSIZE in the macro
NTPRM is exceeded.
|
Action |
Increase the maximum size of OVSIZE or
WPSIZE of the macro NTPRM .
|
NUS0228 - GETMAIN FOR BIT TABLE BUFFER FAILED
Explanation |
Internal error. |
Action |
Send the corresponding dump to Software AG Support. |