Messages from Program CMPSTART

This document contains the error messages (CMPnnnn) that may be issued by the program CMPSTART whose task is to start global common memory pools in Natural under BS2000/OSD.

For information on the program CMPSTART, see Common Memory Pools in the Natural Operations documentation.


CMP0001 - p o o l n a m e : GLOBAL POOL IS ACTIVATED

Explanation The common memory pool is successfully enabled and activated.
Action None.

CMP0002 - d a t a s p a c e n a m e : DATA SPACE CREATED

Explanation ESA Data Space is successfully created.
Action None.

CMP0003 - NO PARAMETERS ON SYSDTA FOUND

Explanation In SYSDTA, the parameter definitions are missing.
Action Check the job control for execution of CMPSTART.

CMP0004 - READING PARAMETERS FROM SYSDTA FAILED

Explanation Error from RDATA macro.
Action Check the job control for execution of CMPSTART.

CMP0005 - p o o l n a m e : GLOBAL POOL TERMINATED NORMALLY

Explanation Common memory pool successfully terminated.
Action None.

CMP0006 - d a t a s p a c e n a m e : DATA SPACE SUCCESSFULLY DESTROYED

Explanation The ESA Data Space was successfully destroyed.
Action None.

CMP0007 - p o o l n a m e : GLOBAL POOL ABNORMALLY TERMINATED BY OPERATOR REQUEST

Explanation Common memory pool terminated from operator via console.
Action None.

CMP0008 - p o o l n a m e : GLOBAL POOL TERMINATED BY CANCEL

Explanation Common memory pool terminated with CANCEL command.
Action None.

CMP0009 - p o o l n a m e : ERROR IN MACRO n a m e POOL NOT ALLOCATED, R15=nn

Explanation An error from macro n a m e has occurred. R15 contains the error number.
Action Contact Software AG Support.

CMP0010 - p o o l n a m e : REQUESTED POOL IS ALREADY ENABLED

Explanation A common memory pool with the defined name is already enabled.
Action Change the common memory pool name.

CMP0011 - p o o l n a m e : A GLOBAL NATURAL LOAD POOL MUST BE ENABLED WITH "PFIX=YES"

Explanation For a global Natural Load Pool parameter PFIX is defined with NO (default).
Action Define PFIX=YES for the Natural Load Pool.

CMP0012 - p o o l n a m e : NATURAL t y p e POOL INITIALIZATION FAILED, POOL NOT ALLOCATED, R15=nn

Explanation An error during Buffer/Editor/Swap Pool initialization has occurred. R15 containes the error number.
Action Contact Software AG Support.

CMP0013 - DEFINITION OF KEYWORD PARAMETER n a m e MISSING

Explanation To enable the common memory pool, the keyword parameter n a m e must be defined.
Action Complete the parameters for this common memory pool.

CMP0014 - THE OPERAND OF KEYWORD PARAMETER n a m e IS NOT VALID

Explanation Invalid operand for keyword parameter n a m e.
Action Correct the operand for the appropriate keyword parameter.

CMP0015 - THE OPERAND OF KEYWORD PARAMETER n a m e EXCEEDS THE MAX. LENGTH

Explanation The operand of keyword parameter n a m e is too long.
Action Correct the operand for the appropriate keyword parameter.

CMP0016 - n a m e IS NOT A VALID NAME FOR A KEYWORD PARAMETER

Explanation Unknown keyword parameter n a m e.
Action Correct the name of the keyword parameter.

CMP0017 - SPECIFIED SIZE IS TO BIG FOR LOCATION ABOVE

Explanation The defined pool size (operand of keyword parameter SIZE) exceeds the possible maximum size (2047 megabytes) for a pool location above the 16-MB line.
Action Correct the operand of keyword parameter SIZE.

CMP0018 - SPECIFIED SIZE IS TO BIG FOR LOCATION BELOW

Explanation The defined pool size (operand of keyword parameter SIZE) exceeds the possible maximum size (10 megabytes) for a pool location below the 16-MB line.
Action Correct the operand of keyword parameter SIZE

CMP0019 - ADDRESS ABOVE 13 MB IS INVALID FOR LOCATION BELOW

Explanation The defined number of megabyte (operand of keyword parameter ADDR) exceeds the possible maximum number (13 megabytes) for a pool location below the 16-MB line.
Action Correct the operand of keyword parameter ADDR.

CMP0020 - ADDRESS BELOW 16 MB IS INVALID FOR LOCATION ABOVE

Explanation The defined number of megabyte (operand of keyword parameter ADDR) must not be lower than 16 megabytes for a pool location above the 16-MB line.
Action Correct the operand of keyword parameter ADDR.

CMP0021 - WHEN "TYPE" IS DEFINED, DEFINITION OF "LIBR" IS NOT ALLOWED

Explanation The parameter LIBR is only allowed for a Load Pool. For the definition of a Load Pool, the parameter TYPE is not allowed.
Action Correct the pool definition.

CMP0022 - A LIBRARY IS DEFINED; OPERAND OF "NAME" GREATER 8 CHARACTERS

Explanation The name of a module which shall be loaded into a common memory pool must not exceed 8 characters.
Action Correct the operand of keyword parameter NAME.

CMP0023 - THE NAME OF NATURAL BUFFER POOL EXCEEDS 8 CHARACTERS

Explanation The name of a Natural buffer pool (TYPE=NAT) must not exceed 8 characters.
Action Correct the operand of keyword parameter NAME.

CMP0024 - IF "PFIX=YES" IS DEFINED, THE OPERAND OF PARAMETER "ADDR" MUST BE DEFINED ALSO

Explanation When the address of a common memory pool shall be fixed, the operand of keyword parameter ADDR must be defined.
Action Define the operand of keyword parameter ADDR.

CMP0025 - ONE OPERAND OF PARAMETER "TYPE" OR "LIBR" IS MISSING

Explanation For a load pool, the parameter LIBR is necessary and for all other pools the definition of parameter TYPE must be done.
Action Correct the pool definition.

CMP0026 - IF "DESA=YES" IS DEFINED, PARAMETER "DATA=" MUST BE ALSO DEFINED

Explanation When ESA Data Space shall be allocated, the size of the data space must be defined.
Action Define the operand of keyword parameter DATA.

CMP0027 - WITH AN ESA DATA SPACE REQUEST, PARAMETER "LIBR" MUST NOT DEFINED

Explanation For a load pool (parameter LIBR is defined), the request for ESA Data Space is disallowed and vice versa.
Action Correct the pool definition.

CMP0028 - IF MACRO "ASHARE" SHALL BE USED, "PFIX=YES" MUST BE DEFINED

Explanation When a module shall be loaded with macro ASHARE into a load pool (LOAD=ASHARE), PFIX=YES must be defined.
Action Correct the operand of keyword parameter PFIX.

CMP0029 - CMPSTART RUNS ONLY WITH BS2000 VERSION 10.0 AND UP

Explanation The execution of CMPSTART is not possible under BS2000/OSD with a version lower than 10.0.
Action None.

CMP0030 - ERROR IN OPERATOR REQUEST, COMMAND NOT FOUND

Explanation The command from an operator request was invalid.
Action Retry the request with a valid command.

CMP0031 - Job variable name: ERROR FROM MACRO name, R15=nn

Explanation During execution of the job variable, an error from macro name has occurred. R15 contains the error number.
Action Contact Software AG Support.