This document describes special considerations on how to use print files and work files in Natural for VM/CMS.
The following topics are covered:
Print files and work files are defined in the Natural parameter module
with the macros NTPRINT
and
NTWORK
. The corresponding dynamic parameters are
PRINT
and WORK
.
In the following, the subparameters AM
(access
method) and DEST
(destination) are described: They are
available both in NTPRINT
and
NTWORK
.
For both print and work files, Natural/CMS provides two access methods: "STD" and "CMS".
(AM=STD
)
This access method uses the CMS simulation of the z/OS QSAM access
method. Specify AM=STD
if you want to read or write tape or spool
(RDR, PRT, PUN) files, or if you want to read work files from z/OS-formatted
disks.
A FILEDEF
command must be issued before the
corresponding print or work file is opened. The DD name to be used in the
FILEDEF
command is the name specified in the
subparameter DEST
.
(AM=CMS)
This access method uses the standard CMS file system to read and write CMS files on accessed mini disks and SFS directories.
The file names of the resulting CMS files are:
CMPRTnn
for print files,
CMWKFnn
for work files
where nn denotes the number of the file.
Their file type is the same as the name specified in the subparameter
DEST
. The filemode is always
"A1".
DEST=FD |
Destination FD allows greater flexibility in assigning a CMS
file to a Natural print or work file. When Natural opens a print or work file
with destination FD, it searches for a FILEDEF for
the DD name CMPRTnn or
CMWKFnn , respectively (where
nn denotes the print or work file number). It then
uses the CMS file ID given in the FILEDEF
command.
|
DEST=LISTING |
This DEST setting applies to print files
only.
When specifying this destination, the print file is written to the
CMS disk that has the most free space available. The CMS file ID is
|
DEST=UEXxxxxx |
This If you specify a destination that starts with |
Example 1:
When the following FILEDEF
s and NATPARM
settings are in effect
FILEDEF CMWKF05 CLEAR FILEDEF CMPRT01 DISK MY REPORT D FILEDEF CMPRT04 DISK MY REPORT A
NTWORK (1),AM=CMS,DEST=FRED NTWORK (5),AM=CMS,DEST=FD NTWORK (6),AM=CMS,DEST=PAUL NTPRINT (1,4),AM=CMS,DEST=FD NTPRINT (2),AM=CMS,DEST=LISTING NTPRINT (5),AM=CMS,DEST=PAUL
the following CMS files are produced:
CMWKF01 FRED A1 FILE CMWKF05 A1 CMWKF06 PAUL A1
MY REPORT D1 MY REPORT A1 CMWKF05 PAUL A1
The temporary file CMPRT02 LISTING
m
is printed and subsequently deleted (where
m denotes the filemode of the minidisk that had the
most free space).
Example 2:
NTPRINT (1),AM=CMS,DEST=UEXLOCAL
produces the CMS file:
CMPRT01 UEXLOCAL m
and the CMS command UEXLOCAL
is issued with
the file ID as parameter. If, for example, a Rexx procedure of this name
exists, it can determine for which printer it was invoked by using arg fn
ft fm
.
Example 3:
Destinations can also be defined dynamically using the
DEFINE WORK FILE
statement. In addition, DEFINE WORK FILE
can be used to specify
input from, or output to, a Rexx stem:
DEFINE WORK FILE n 'STEM rexxstem.'
When opening an input file, Natural uses the value of
rexxstem.0
to determine the number of
records to read. It then reads records from
rexxstem.1 to
rexxstem.max (with
max = rexxstem.0)
before returning end-of-data.
For an output file, Natural writes
rexxstem.1
to
rexxstem.n
,
and sets rexxstem.0
to n
when the work file is closed.