GETMAIN Error Numbers in NAT7545
This document describes the error numbers which are displayed in Error
Message NAT7545 as a result of a failed GETMAIN request:
NAT7545 getmain of :1: for :2: buffer failed (:3:/:4:)
where :3: contains one of the following
error numbers and
:4: may contain length-specific
information which is explained below, or the response code from the operating
system.
Error 04 : Thread upper limit exceeded
| Expl. |
The Natural user thread is too
small.
|
| Actn. |
Increase the Natural thread
length.
|
Error 08 : Invalid buffer type
| Expl. |
Internal error, the buffer type
used is not valid.
|
| Actn. |
Contact Software AG Support.
|
Error 12 : Compression table is full
| Expl. |
Internal error, upper limit of
the compression table exceeded.
|
| Actn. |
Contact Software AG Support.
|
Error 16 : Buffer already exists
| Expl. |
Internal error, a GETMAIN for an
existing buffer was executed.
|
| Actn. |
Contact Software AG Support.
|
Error 20 : 1st requested buffer was not the PCB
| Expl. |
Internal error, Natural Permanent
Control Block missing.
|
| Actn. |
Contact Software AG Support.
|
Error 24 : Invalid GETMAIN length
| Expl. |
Internal error, the buffer length
of a GETMAIN is invalid.
|
| Actn. |
Contact Software AG Support.
|
Error 28 : Address Physical Buffer Table missing
| Expl. |
Internal error, address of
Physical Buffer Table not found.
|
| Actn. |
Contact Software AG Support.
|
Error 32 : Physical Buffer Table is full
| Expl. |
Internal error, upper limit of
Physical Buffer Table exceeded.
|
| Actn. |
Contact Software AG Support.
|
Error 36 : Incorrect Buffer Prefix Table entry (CMBPFT)
| Expl. |
Internal error, Buffer Prefix
Table entry in
NATCONFG
is destroyed.
|
| Actn. |
Contact Software AG Support.
|
Error 40 : Physical freemain not done
| Expl. |
Internal error, freemain of the
work pools not done.
|
| Actn. |
Contact Software AG Support.
|
Error 44 : Work Pool or Fixed Buffer allocated above instead below
| Expl. |
Internal error, work pool or
fixed buffer not allocated below the 16-MB line.
|
| Actn. |
Contact Software AG Support.
|
Error 48 : Address of Buffer Prefix Table entry not resolved
| Expl. |
The address of entry CMBPFT in
module NATCONFG is not resolved.
|
| Actn. |
Module
NATCONFG
must be linked to the Natural nucleus.
|
Error 52 : Error from CMGETMP - see :4: in message NAT7545
| Expl. |
Physical GETMAIN error from the
operating system.
|
| Actn. |
For details, see reason code and
response code from operating system.
|
Error 56 : Thread overflow size greater defined OVSIZE in NTPRM
:4:
Error 60 : Getmain buffer size lower min. Buffer size
| Expl. |
Internal error, the buffer length
is lower than the minimum buffer size.
|
| Actn. |
Contact Software AG Support.
|
Error 64 : Getmain buffer size greater max. buffer size
| Expl. |
Internal error, buffer length is
greater than the maximum buffer size.
|
| Actn. |
Contact Software AG Support.
|
Error 68 : Total size of work pools below the line exceeds max.
size
:4:
| Expl. |
The total size of all work pools
below the 16-MB line exceeds the defined max. size in the 3rd operand of
keyword parameter WPSIZE in the Natural parameter module (macro NTPRM).
|
| Actn. |
Increase the 3rd operand of the
keyword parameter WPSIZE in the
macro NTPRM.
|
Error 72 : Total size of work pools above the line exceeds max.
size
:4:
| Expl. |
The total size of all work pools
above the 16-MB line exceeds the defined max. size in the 4th operand of
keyword parameter WPSIZE in the Natural parameter module (macro NTPRM).
|
| Actn. |
Increase the 4th operand of the
keyword parameter WPSIZE in the
macro NTPRM.
|
