Version 4.2.6
 —  Natural for MBCS  —

Installing Natural for MBCS under z/OS

This section describes step by step how to install Natural for MBCS (product code NKA) under the operating system z/OS using Adabas system files.

This section covers the following topics:

See also z/OS Environment in the Operations documentation.

For installation-related information on Unicode and code page support, refer to Configuration and Administration of the Unicode/Code Page Environment in the Unicode and Code Page Support documentation.

Notation vrs or vr:

The notation vrs or vr stands for the relevant version, release, system maintenance level numbers. For further information on product versions, see Version in the Glossary.


Prerequisites

For further information, refer to the products and versions specified under Natural and Other Software AG Products and Operating and Teleprocessing Systems Required in the current Natural Release Notes for Mainframes.

Top of page

Installation Tape for Natural for MBCS under z/OS

The installation tape contains the datasets listed in the table below. The sequence of the datasets and the number of library blocks needed are shown in the Report of Tape Creation which accompanies the installation tape.

Dataset Name Contents
NKAvrs.LOAD Natural for MBCS load modules.
NKAvrs.INPL Natural for MBCS system objects.

Copying the Tape Contents to a z/OS Disk

If you are using SMA, refer to the System Maintenance Aid documentation (included in the current edition of the Natural documentation CD).

If you are not using SMA, follow the instructions below.

This section explains how to:

The JCL in this dataset is then used to copy all datasets from tape to disk.

If the datasets for more than one product are delivered on the tape, the dataset COPY.JOB contains the JCL to unload the datasets for all delivered products from the tape to your disk.

After that, you will have to perform the individual install procedure for each component.

Step 1 - Copy Dataset COPY.JOB from Tape to Disk

The dataset COPY.JOB (Label 2) contains the JCL to unload all other existing datasets from tape to disk. To unload COPY.JOB, use the following sample JCL:

//SAGTAPE JOB SAG,CLASS=1,MSGCLASS=X
//* ---------------------------------
//COPY EXEC PGM=IEBGENER
//SYSUT1 DD DSN=COPY.JOB,
// DISP=(OLD,PASS),
// UNIT=(CASS,,DEFER),
// VOL=(,RETAIN,SER=tape-volume),
// LABEL=(2,SL)
//SYSUT2 DD DSN=hilev.COPY.JOB,
// DISP=(NEW,CATLG,DELETE),
// UNIT=3390,VOL=SER=volume,
// SPACE=(TRK,(1,1),RLSE),
// DCB=*.SYSUT1
//SYSPRINT DD SYSOUT=*
//SYSIN DD DUMMY
// 

where:

hilev is a valid high level qualifier
tape-volume is the tape volume name, for example: T12345
volume is the disk volume name

Step 2 - Modify COPY.JOB on Your Disk

Modify the COPY.JOB on your disk to conform to your local naming conventions and set the disk space parameters before submitting this job:

Step 3 - Submit COPY.JOB

Submit COPY.JOB to unload all other datasets from the tape to your disk.

Top of page

Installation Procedure

Step 1 - Relink the Natural Nucleus to Include the Natural for MBCS Module

(Jobs I060 and I080 from the Natural installation tape)

Relink your Natural nucleus to include the Natural for MBCS module:

 INCLUDE NKALOAD(NKANUC)

You must link the NKANUC module to all Natural nuclei that should make use of the features supplied by Natural for MBCS. Software AG recommends that you relink Natural with the NKANUC module.

To avoid the need to relink Natural with NKANUC, specify the Natural profile parameters RCA and RCALIAS either dynamically or in the NATPARM parameter module:

RCA=NATGWNKA,RCALIAS=(NATGWNKA,NKANUC)

Step 2 - Load the System Programs

(Job I061, Step 8200)

Use the Natural utility INPL to load the Natural system objects (dataset NKAvrs.INPL) into the Natural system file.

Top of page

Installation Verification for Natural for MBCS

After the last step of the installation procedure has been successfully performed, start Natural and enter the command EDIT MAP at the command prompt. The Edit Map menu should then appear with the additional menu option Outline Editor.

Top of page