UQ Spool Processing

The record number specified on the LR operand does not exist in the data set being displayed.

Displays the message and continues processing.

Enter a valid LR operand.

The data set number specified on the DS operand does not exist in the job being displayed.

Displays the message and continues processing.

Enter a valid DS operand.

The job specified on the JB operand does not exist.

Displays the message and continues processing.

Enter a valid JB operand.

The user started a SCAN function and then interrupted it by pressing the RESET key and ENTER again.

The SCAN function is terminated.

None.

The user attempted to look at job output by specifying SI=SO but the job is in the input queue.

Displays the message and continues processing.

None.

The user attempted to look at job input but the job specified is in the output queue.

Displays the message and continues processing.

None.

The job selected has been secured by the user who submitted it; the user requesting the job does not have the authority to do so.

Displays the message and continues processing.

None.

An error occurred during the PSOPEN processing.

UQ is abended and control is returned to COM-PASS.

Contact the Com-plete system programmer.

The physical end of the output data set has been reached.

Displays the message and continues processing.

None.

This message is associated with the Com-plete online utility UQ. The terminal user has requested Com-plete to display the status of a job or jobs in the job queue, but no jobs were found that met the specified selection criteria.

The request is not processed.

The request should be modified to broaden the selection criteria. Change the selection parameters such as CL=, DE=, JB=, and JC=. Refer to Com-plete User Utilities Manual for more information.

None.

This message is associated with the Com-plete online utility UQ. The terminal user has made a request for system output data from a batch job; however, the job is presently queued for execution. Therefore, system output data is not yet available.

The request is not processed.

Retry the request once the job is awaiting output.

This message is not applicable to the VS/2 operating system in which system output files are available as they are created.

This message is associated with the Com-plete online utility UQ. The terminal user made a request for system output data from a batch job; however, the job is presently executing and has not yet queued output for the system. Therefore, system output data is not yet available.

The request is not processed.

None.

This message is not applicable to the VS/2 operating system in which system output files are available as they are created.

This message is associated with the S(pool) function of Com-plete's online utility UQ. It is written as the last line of a printout file when a copy of a job is sent to a terminal using the PT keyword.

None.

The function of this message is to flag the end of a job. No action is necessary.

This message is associated with the Com-plete online utility UQ. The JES dataset could currently not be allocated.

The request is not processed.

Check if there are additinal ESY messages in the log. If not, retry the request.

Retry the request. If the error persists, contact the Com-plete system programmer.

The terminal operator has made a request for system output from a batch job; however, a logical error was detected while attempting to read the JES3 spool. This can occur in the following circumstances:

1. The job being displayed is currently executing, and an attempt is being made to display past the current end of the system output.

2. The job being displayed is purged from the JES3 system while it is being displayed.

3. There is a bad JES3 control block associated with the job being displayed.

The request is not processed.

Retry the request. If the error persists, contact the Com-plete system programmer.

If the job is not executing and has not been purged, consider a JES3 warmstart or warmstart with analysis.

This message is associated with the Com-plete online utility UQ. The terminal operator has made a request to display system output from a batch job; however, a sysout record greater than 255 characters was encountered. This applies to JES3 systems.

The request is not processed.

The selected file may not be displayed at the terminal.

Self-explanatory message.

A NOTE command was issued and there was no room for additional NOTEs.

The request is not processed.

No more NOTEs may be added to the job output.

A POINT command was issued that specified an unknown NOTE label.

The request is not processed.

Correct the POINT command and reenter.

A NOTE command specified a label longer than 8 characters.

The request is not processed.

Correct the NOTE command and reenter.

The user has aborted a print request.

Informational only.

Informational only.

The terminal operator has made a request for system output from a batch job; however, a logical error was detected while attempting to read the JES2 spool. This can occur in the following circumstances:

1. The job being displayed is currently executing, and an attempt is being made to display past the current end of the system output.

2. The job being displayed is purged from the JES2 system while it is being displayed.

3. There is a bad JES2 control block associated with the job being displayed.

The request is not processed.

Retry the request. If the error persists, contact the Com-plete system programmer.

If the job is not executing and has not been purged, consider a JES2 warmstart or warmstart with analysis.

Self-explanatory message.