Reentrant Program Support

This message is associated with Com-plete initialisation of resident programs and indicates the program '$' is not in the Com-plete STEPLIB, JOBLIB, or SYS1.LINKLIB libraries.

The application program that was to be loaded as resident is not loaded.

Link edit the resident program then restart Com-plete.

The program '$' is not loaded resident. If, at a later time, the program is link edited to one of the above libraries and is subsequently loaded by an application program, it will be loaded into the thread. If not enough storage is available, the application program will be abnormally terminated.

This message is associated with Com-plete initialisation of resident programs. The number indicated by CODE $2 indicates the type of error and represents the return code from the operating system LOAD macro. Please refer to the appropriate operating system manuals for a description of the LOAD macro's return code.

The application program that was to be loaded as resident is not loaded.

Link edit the resident program and then restart Com-plete.

The program '$1' is not loaded resident. If an application program subsequently loads program '$1', it will be loaded into the thread. If not enough storage is available, the application program will be abnormally terminated.

Self-explanatory message.

Self-explanatory message.

Resident program $1 was load successfully. For systems where modules can reside above the 16 meg line, $2 indicates if it was loaded 'ABOVE' or 'BELOW'. If the program is not reentrant, $3 will indicate that fact. Residentpage programs must be reentrant, otherwise abends will occur when the program tries to alter itself.

This message indicates how many resident programs were loaded ($1) and the total size of the resident programs ($3). For systems where modules can reside above the 16 meg line, $2 indicates which 'set' of modules the message relates to ie. one message will be issued for the modules loaded below the line and one for the modules loaded above.

This information can be used to estimate the storage requirements of for Com-plete.

The same program name $1 has been specified twice in the Com-plete startup parameters.

Program $1 is loaded once into the resident program area and the second request is ignored.

Remove one of the RESIDENTPAGE sysparm for the duplicated module.

The operand entered is not 'LOAD', 'DELETE', or 'REFRESH'.

The command is ignored.

Correct the command and reenter.

The specified program name does not start with a letter or is more than eight characters long.

The command is ignored.

Correct the command and reenter.

A request was made to load a program which was already resident.

The command is ignored.

Specify the 'REFRESH' operand.

An operator request $2 for resident program $1 has completed successfully. If the request involved the loading or refreshing of a program, $3 will indicate if the program was loaded above or below the 16 meg line and if the newly loaded program is reentrant or not.

A LOAD request failed because the specified program could not be found.

The command is ignored.

Place the specified program in Com-plete STEPLIB/LIBDEF. STEPLIB/LIBDEF.

Notify the Com-plete system programmer.

A request to load a module into the resident program area has been received. Com-plete attempted to get storage for a Loaded Program Control Block (LPCB) for the module and this request has failed.

The request to load the program is terminated without the program being loaded.

In a case where storage is not available for the LPCB, it is unlikely that the storage will be available to load the actual module. In this case, the storage estimates must be reviewed to allow for situations where modules must be loaded while Com-plete is running.

A PGM DELETE or REFRESH command specified a module that cannot be deleted immediately, because one or more processes are busy using it and might abend if the module was deleted.

The module is flagged as deleted, but will only be deleted physically when the last process frees it.

In case of a REFRESH command, or if the module will be requested to be loaded, a new copy of the module will be loaded into the Com-plete region, provided that enough memory is available.

A request was made for action against resident program $1, however, Com-plete has determined that this program does not exist in the resident program area.

A call to the Com-plete resident program search module has resulted in an unexpected return code.

The request is terminated.

Contact your local support centre with the details of the exact command issued which caused the problem.