LPR0001 | LPR0002 | LPR0003 | LPR0004 | LPR0005 | LPR0006 | LPR0007 | LPR0100 | LPR0103 | LPR0105| LPR0001 | Invalid Parameter address |
| Explanation: |
The addresses in the parameter list for the request are incorrect |
| System action: |
The program is cancelled. |
| Appl. programmer info: |
Make sure all addresses in your parameter list are correct |
| LPR0002 | Wrong command sequence |
| Explanation: |
A PSPUT was issued without a prior PSOPEN |
| System action: |
The program is cancelled. |
| Appl. programmer info: |
Correct your program logic. |
| LPR0003 | No buffer avaliable |
| Explanation: |
A request for an element of one of Com-plete's bufferpool was not successful. |
| System action: |
The program is cancelled. |
| System programmer info: |
Check for further consol messages indicating storage problems in the Com-plete region. |
| LPR0004 | Attach of $1 failed with returncode $2 |
| Explanation: |
Program RCANLPR could not be attached to send the printout to the (server)queue, e.g because there was no free tib entry available. |
| System action: |
The program is normally terminated and the printout buffers are kept. |
| System programmer info: |
Check the returncode of the ATTACH function and correct the error. |
| Appl. programmer info: |
Check the returncode of the ATTACH function and correct the error. |
| LPR0005 | The logical output driver $1 could not be loaded |
| Explanation: |
The logical output driver indicated in the PSCB could not be loaded. |
| System programmer info: |
Check that you set the correct name and that there was enough storage available to load the module. There might be more consol messages regarding a failing LOAD request. |
| Appl. programmer info: |
Check that you set the correct name and that there was enough storage available to load the module. There might be more consol messages regarding a failing LOAD request. |
| LPR0006 | Bad returncode $1 from the logical output driver $2 |
| Explanation: |
Your logical output driver couldn't handle your request. |
| Appl. programmer info: |
Check the original printout, program and output driver for any kind of logic errors. |
| LPR0007 | MAXPOLINES ( $1 ) exceeded |
| Explanation: |
Your program tried to create a bigger spool file than the sysparm MAXPOLINES allowed. |
| System action: |
The program is terminated and the printout discarded. |
| System programmer info: |
Check with your application programmer if the sysparm should be increased. |
| Appl. programmer info: |
Make sure your program didn't run into a loop and the high number of lines is correct. |
| LPR0100 | &1: PRINTOUT FROM &2 TO &2 DISCARDED |
| Explanation: |
The printout with the internal number &1 sent from userid &2 to printer &3 has been deleted. |
| System action: |
The printout with the internal number &1 sent from userid &2 to printer &3 has been deleted because it could not be delivered to the printer. |
| System programmer info: |
Check previous LPR message for the reason. |
| LPR0103 | &1: Host not found: &2 : name does not resolve for the supplied parms |
| Explanation: |
The printout with the internal number &1 could not be delivered because the server &2 could not be found |
| System action: |
The printout is deleted |
| System programmer info: |
Correct the server name (either in UDEF or in the ENVIRONment variables). |
| LPR0105 | &1: Timed Out |
| Explanation: |
The printout with the internal number &1 could not be delivered to the print server |
| System action: |
We waitsd 10 minutes for the print server to accept the printout. After this time the printout will be discarded. |