Adabas Review 00xxx Messages

Overview of Messages

REV00MNF | REV00001 | REV00002 | REV00003 | REV00004 | REV00005 | REV00006 | REV00008 | REV00011 | REV00012 | REV00013 | REV00014 | REV00015 | REV0001 | REV00020 | REV00021 | REV00025 | REV00026 | REV0002 | REV00028 | REV00029 | REV00030 | REV00032 | REV00033 | REV00035 | REV00036 | REV00037 | REV00038 | REV00040 | REV00043 | REV00044 | REV00045 | REV00046 | REV00047 | REV00050 | REV00054 | REV00055 | REV00057 | REV00058 | REV00059 | REV00060 | REV00062 | REV00064 | REV00065 | REV00066 | REV00068 | REV00072 | REV00073 | REV00074 | REV00078 | REV00079 | REV00080 | REV00081 | REV00082 | REV00083 | REV00084 | REV00085 | REV00086 | REV00087 | REV00091 | REV00092 | REV00093 | REV00094 | REV00095 | REV00096 | REV00097 | REV00098 | REV00099 | REV00100 | REV00101 | REV00102 | REV00104 | REV00105 | REV00106 | REV00108 | REV00111 | REV00116 | REV00120 | REV00121 | REV00123 | REV00124 | REV00125 | REV00129 | REV00132 | REV00133 | REV00134 | REV00135 | REV00137 | REV00138 | REV00139 | REV00140 | REV00141 | REV00144 | REV00145 | REV00146 | REV00147 | REV00148 | REV00149 | REV00150 | REV00151 | REV00152 | REV00153 | REV00155 | REV00156 | REV00157 | REV00158 | REV00159 | REV00160 | REV00161 | REV00162 | REV00163 | REV00169 | REV00170 | REV00171 | REV00175 | REV00176 | REV0017 | REV00179 | REV00180 | REV00181 | REV00182 | REV00183 | REV00184 | REV00185 | REV00187 | REV00188 | REV00190 | REV00193 | REV00195 | REV00196 | REV00197 | REV00198 | REV00199 | REV00200 | REV00202 | REV00203 | REV00205 | REV00206 | REV00207 | REV00209 | REV00210 | REV00211 | REV00212 | REV00214 | REV00217 | REV00218 | REV00219 | REV00220 | REV00221 | REV00222 | REV00223 | REV00224 | REV00225 | REV00226 | REV00227 | REV00228 | REV00229 | REV00230 | REV00231 | REV00234 | REV00235 | REV00236 | REV00237 | REV00238 | REV00239 | REV00240 | REV00241 | REV00242 | REV00243 | REV00244 | REV00245 | REV00246 | REV00247 | REV00248 | REV00249 | REV00250 | REV00252 | REV00253 | REV00254 | REV00255 | REV00256 | REV00257 | REV00258 | REV00259 | REV00260 | REV00261 | REV00262 | REV00263 | REV00264 | REV00265 | REV00266 | REV00267 | REV00268 | REV00269 | REV00270 | REV00271 | REV00272 | REV00273 | REV00274 | REV00275 | REV00276 | REV00277 | REV00278 | REV00279 | REV00280 | REV00281 | REV00282 | REV00283 | REV00284 | REV00285 | REV00286 | REV00288 | REV00289 | REV00290 | REV00291 | REV00292 | REV00293 | REV00294 | REV00295 | REV00296 | REV00297 | REV00299 | REV00300 | REV00301 | REV00306 | REV00307 | REV00308 | REV00309 | REV00310 | REV00311 | REV00312 | REV00313 | REV00314 | REV00315 | REV00316 | REV00317 | REV00318 | REV00319 | REV00320 | REV00321 | REV00322 | REV00323 | REV00325 | REV00326 | REV00327 | REV00328 | REV00329 | REV00330 | REV00331 | REV00332 | REV00333 | REV00334 | REV00335 | REV00336 | REV00337 | REV00338 | REV00339 | REV00340 | REV00341 | REV00342 | REV00343 | REV00344 | REV00345 | REV00346 | REV00347 | REV00348 | REV00349 | REV00350 | REV00351 | REV00352 | REV00353 | REV00354 | REV00355 | REV00356 | REV00357 | REV00359 | REV00360 | REV00361 | REV00362 | REV00363 | REV00364 | REV00365 | REV00366 | REV00367 | REV00368 | REV00369 | REV00370 | REV00371 | REV00372 | REV00373 | REV00374 | REV00375 | REV00385 | REV00386 | REV00388 | REV00390 | REV00391 | REV00392 | REV00393 | REV00394 | REV00395 | REV00396 | REV00397 | REV00398 | REV00399 | REV00400 | REV00401 | REV00402 | REV00403 | REV00404 | REV00405 | REV00406 | REV00407 | REV00408 | REV00409 | REV00410 | REV00411 | REV00412 | REV00413 | REV00414 | REV00415 | REV00416 | REV00417 | REV00418 | REV00419 | REV00420 | REV00421 | REV00422 | REV00423 | REV00424 | REV00425 | REV00426 | REV00427 | REV00428 | REV00429 | REV00430 | REV00431 | REV00432 | REV00433 | REV00434 | REV00435 | REV00436 | REV00437 | REV00438 | REV00439 | REV00440 | REV00441 | REV00442 | REV00443 | REV00444 | REV00445 | REV00446 | REV00447 | REV00448 | REV00449 | REV00450 | REV00451 | REV00453 | REV0454 | REV00455 | REV00456 | REV00457 | REV00458 | REV00459 | REV00460 | REV00461 | REV00462 | REV00463 | REV00464 | REV00465 | REV00466 | REV00467 | REV00468 | REV00469 | REV00470 | REV00471 | REV00472 | REV00473 | REV00474 | REV00475 | REV00476 | REV00477 | REV00478 | REV00479 | REV00480 | REV00481 | REV00482 | REV00483 | REV00484 | REV00485 | REV00486 | REV00487 | REV00488 | REV00489 | REV00490 | REV00491 | REV00492 | REV00493 | REV00494 | REV00495 | REV00496 | REV00497 | REV00498 | REV00499 | REV00500 | REV00501 | REV00502 | REV00503 | REV00504 | REV00505 | REV00506 | REV00507 | REV00508 | REV00509 | REV00510 | REV00511 | REV00512 | REV00513 | REV00514 | REV00515 | REV00516 | REV00517 | REV00518 | REV00519 | REV00520 | REV00521 | REV00522 | REV00523 | REV00524 | REV00525 | REV00526 | REV00527 | REV00528

REV00MNF Message msg-id not found in logon-id
Explanation

A message inquiry was made for a message number that is not known to Adabas Review. This will happen if an invalid message number is entered.

Action

If the message number is for an Adabas Review message, contact your Software AG technical support representative.


REV00001 Welcome to Adabas Review V v.r.s running under tp-monitor
Explanation

This message welcomes users to Adabas Review and indicates the environment under which they are running.

v.r.s the version, revision, and SP level.
tp-monitor the active TP monitor.
Action

This message is for information only.


REV00002 Review command must begin with subsystem code
Explanation

An invalid command was entered from the Adabas Review main menu. All commands from the main menu must begin with a subsystem code as shown on the screen.

Action

Enter a valid command.


REV00003 THIS FIELD IS NOT ALLOWED FOR DETAIL REPORTS
Explanation

The specified filed is not allowed for detailed reports.

Action

Remove the incorrect field.


REV00004 Enter Review command
Explanation

Adabas Review is waiting for terminal input.

Action

Press a valid PF key or enter an Adabas Review command.


REV00005 Invalid command
Explanation

An invalid command was entered into the Adabas Review command line.

Action

Press a valid PF key or enter a valid Adabas Review command.


REV00006 Press 'Enter' to continue initialization process
Explanation

During Adabas Review initialization a series of messages are displayed. Adabas Review will pause whenever a page is full or on the last page.

Action

Press ENTER.


REV00008 No online system of Review is available
Explanation

Adabas Review has determined that there are no online systems available to the user. There are two possible causes:

  1. the installation of Adabas Review has not been fully completed.

  2. Adabas Review is installed, but your profile prohibits you from accessing the available systems.

Action

Contact your Adabas Review administrator.


REV00011 Interval statistics profile has been created
Explanation

During Adabas Review initialization, the interval statistics profile record was created.

Action

This message is for information only.


REV00012 Report has been saved
Explanation

The request to save a report definition to the Adabas Review repository has completed successfully.

Action

This message is for information only.


REV00013 Now viewing current data
Explanation

You are now viewing current data as opposed to historical data.

Action

This message is for information only.


REV00014 user-id is not authorized to use Review
Explanation

Either you have not been defined to Adabas Review, or you are not authorized to use Adabas Review.

Action

Contact your Adabas Review administrator.


REV00015 Report name is required
Explanation

An attempt was made to edit/copy a report without a name.

Action

Enter a name in the report name field.


REV0001 At least one item must be selected
Explanation

An attempt was made to add a report without selecting any items to be used as report criteria.

Action

Select one or more fields to be used as criteria by entering a number in its ORDER field.


REV00020 Order number must not exceed 20 (max number of items)
Explanation

A number greater that 20 was entered into one of the ORDER fields.

Action

Enter a number between 1 and 20.


REV00021 Order number must be unique
Explanation

Duplicate ORDER numbers have been detected.

Action

Enter a unique number in each ACCT ORDER to be included in the report.


REV00025 Now viewing historical data
Explanation

You are now viewing historical data as opposed to current data.

Action

This message is for information only.


REV00026 Report was not saved
Explanation

The request to save a report was not successful. This is usually caused by responding NO when asked if you want to replace the report that was previously saved under the same name.

Action

This message is for information only.


REV0002 There are no detailed records for this report
Explanation

A detailed response time report was requested but there are no detail records for the selected report.

Action

This message is for information only.


REV00028 Report was not refreshed
Explanation

This indicates that a request to restart a report was not successful.

Action

This message is for information only.


REV00029 Invalid reply
Explanation

An invalid reply was given to an Adabas Review prompt.

Action

Enter a valid reply.


REV00030 Report has been purged
Explanation

This confirms that the purge report request was successful.

Action

This message is for information only.


REV00032 Report not found
Explanation

An attempt to access a report has failed because the report is not active.

Action

This message is for information only.


REV00033 Unknown return code from purge - RC= ret-code
Explanation

An unknown return code was returned from the purge reports program due to an internal error.

Action

If the problem reoccurs, contact your Software AG technical support representative.


REV00035 This is the oldest historical snapshot
Explanation

This is the oldest historical snapshot; the NEXT command cannot be entered.

Action

This message is for information only.


REV00036 Do not enter x and a direct command
Explanation

A reply was entered into an Adabas Review prompt field and a direct command was entered simultaneously.

Action

Either answer the Adabas Review prompt or enter a direct command, but not both.


REV00037 Invalid response - only valid response is xxx
Explanation

An invalid response was detected and Adabas Review is prompting the user with the correct response.

Action

Enter a valid response.


REV00038 Report status has been changed
Explanation

This confirms that a request to activate or deactivate a report was successful.

Action

This message is for information only.


REV00040 Redisplay buffer full - Rediplay unavailable
Explanation

The redisplay is unavailable because more than 5000 lines were displayed.

Action

As a workaround, the report data can be printed via the HC command and other tools can be used to scroll through this output.


REV00043 You must reply 'Y' or 'N'
Explanation

An invalid reply was given in response to an Adabas Review prompt that requires a reply of either yes ("Y") or no ("N").

Action

Reply "Y" or "N".


REV00044 Value must be between 0 and 100
Explanation

The value entered was not within the range 0 and 100.

Action

Enter a value between 0 and 100.


REV00045 Do not mark blank lines
Explanation

A selection was marked on a line that does not have a value or any data to select.

Action

Mark a valid selection or enter an Adabas Review command.


REV00046 Do not mark deleted reports
Explanation

A character was placed in the select field of a report that was just deleted.

Action

Do not place a character in this field.


REV00047 Invalid character
Explanation

An invalid character was entered into an Adabas Review field.

Action

Enter a valid character.


REV00050 Non-zero return code from FREEMAIN
Explanation

An unexpected return code has occurred while trying to free storage. The return code is also displayed.

Action

If the problem recurs, contact your Software AG technical support representative.


REV00054 Now creating sample report report-name
Explanation

When Adabas Review is invoked online for the first time, it adds sample Adabas reports to its system file.

Action

This message is for information only.


REV00055 Select a historical snapshot
Explanation

Select a historical snapshot.

Action

This message is for information only.


REV00057 Use of function is prohibited
Explanation

An attempt was made to perform an Adabas Review function that is not permitted for the user.

Action

Contact your Adabas Review administrator.


REV00058 There are no saved reports to list
Explanation

A request to list report definitions was made but there are no definitions to list.

Action

This message is for information only.


REV00059 Operator command issued
Explanation

The operator command was issued to Com-plete.

Action

This message is for information only.


REV00060 No report selected to view
Explanation

An attempt was made to perform an Adabas Review View function, but no report was selected

Action

Access a report using a List or Edit function and the retry the View function.


REV00062 No data has been accumulated for this report
Explanation

A request to display a report cannot be satisfied because the report has not yet accumulated any data.

Action

Determine if the report criteria is correct and if so, try again later or else add a new report.


REV00064 Invalid function
Explanation

An invalid function was entered.

Action

Enter a valid function.


REV00065 DBID missing
Explanation

DBID= was entered on the Adabas Review command line of the Adabas Communication Statistics display, but no corresponding DBID number was given.

Action

Enter DBID=nnn where nnn is a valid DBID number.


REV00066 Invalid cursor position
Explanation

The cursor was placed at an invalid location on a screen that senses the cursor position to perform a function.

Action

Place the cursor at a valid position or enter an Adabas Review command.


REV00068 Invalid logical operator
Explanation

An invalid logical operator was entered. Valid operators are: =,:,<,>,EQ,NE,LT,GT,LE,GE

Action

Enter a valid logical operator.


REV00072 Mark one line only
Explanation

More than one line was marked to perform a report function. This is not allowed.

Action

Mark only one line at a time.


REV00073 Invalid character in select column
Explanation

A line has been marked with a character that has no assigned function.

Action

Mark lines using valid characters.


REV00074 Invalid Transaction Summary option
Explanation

An invalid option was entered into the Transaction Summary Option field in the Edit Report screen.

Valid options are NONE, SUM, and DET.

Action

Enter a valid option.


REV00078 Report was not purged
Explanation

The request to purge a started report was not performed.

Action

This message is for information only.


REV00079 Invalid message prefix
Explanation

An inquiry was made for a message number that has an invalid prefix. Message numbers must start with REV.

Action

Enter the MSG command using a valid message number.


REV00080 Com-plete functions are not valid under CICS
Explanation

A Com-plete performance monitor function was attempted. This is not valid under CICS.

Action

This message is for information only.


REV00081 Review is not compatible with this version of Com-plete
Explanation

A Com-plete performance monitor function was attempted on a version of Com-plete earlier than version 4.4.

Action

Install the current version of Com-plete.


REV00082 Select a buffer pool or enter a Review command
Explanation

The Adabas Review buffer pool function is waiting for terminal input.

Action

Select a buffer pool by name or enter an Adabas Review command.


REV00083 Syntax error in scan command
Explanation

A syntax error was detected while processing a scan command on the ET display.

Action

This message is for information only.


REV00084 Invalid buffer pool name
Explanation

The buffer pool selection entered cannot be identified.

Action

Enter a valid buffer pool name or enter an Adabas Review command.


REV00085 Command not allowed in history mode
Explanation

The command entered is not allowed in history mode.

Action

Do not enter command.


REV00086 No ADAB control block found
Explanation

The Adabas Communication Statistics function was invoked, but there has not been any database access since Com-plete was started. Therefore, there is no database information to display.

Action

Try again later.


REV00087 nn Reports removed from AUTOSTART status
Explanation

This confirms that the indicated report definitions have been changed from AUTOSTART to NON-AUTOSTART status.

Action

This message is for information only.


REV00091 Invalid command code
Explanation

An invalid code was entered for a command.

Action

Enter a valid command code.


REV00092 Report has been started
Explanation

This confirms that the request to start a report was successful.

Action

This message is for information only.


REV00093 Syntax error(s) in report definition
Explanation

The request to start an online report has failed because of syntax errors in the report definition.

Action

Correct the report definition and start the report again.


REV00094 Adabas response code rsp
Explanation

Adabas has responded with a non-zero response code.

Action

Use the Adabas Messages and Codes documentation to determine the problem.


REV00095 Report was not started
Explanation

The request to start a report was not successful.

Action

This message is for information only.


REV00096 User profile is being held by another user
Explanation

An attempt was made to access a user profile that is being updated by another user.

Action

Edit the user profile again. Ensure that the changes made to profile do not affect the changes that you are making.


REV00097 User profile not specified
Explanation

The purge user (PU) command was given without specifying a user profile.

Action

When using the purge user (PU) command, specify the user profile you wish to purge. The format for the command is PU uuuuuu where uuuuuu is the user profile.


REV00098 User profile was not purged
Explanation

A request was made to purge a user profile. When Adabas Review asked for a confirmation, the user decided not to purge the user profile.

Action

This message is for information only.


REV00099 User profile was not found
Explanation

An attempt was made to delete a user profile that was not found in the Adabas Review repository.

Action

Check to make sure the user ID you specified is correct.


REV00100 User profile has been purged
Explanation

This confirms that a request to purge a user profile was successful.

Action

This message is for information only.


REV00101 New user profile
Explanation

The profile that you are editing is new.

Action

You may now customize the new user profile. To save this new profile, press PF5or issue the SAVE command.


REV00102 User profile was not saved
Explanation

A request was made to save the changes made to a user profile. When Adabas Review asked for a confirmation, the user decided not to save the changes.

Action

This message is for information only.


REV00104 Return code ret-code received from program-name
Explanation

An unexpected return code was received from one of Adabas Review's programs.

Action

Record the error message and contact your Software AG technical support representative.


REV00105 User profile has been saved
Explanation

The changes made to the user profile have been saved.

Action

This message is for information only.


REV00106 No Review control block found
Explanation

(CICS Only) This message appears when REVTAB has not been defined as a resident program.

Action

Contact your Software AG technical support representative.


REV00108 Default user profile has been added
Explanation

This message appears the first time Adabas Review is invoked after installation. A DEFAULT user profile is added to the Adabas Review repository, which allows all users to perform all functions of Adabas Review including the ability to maintain user profiles.

Action

A logical procedure at this point would be to invoke the user profile system and add yourself as able to maintain user profiles. Then update the DEFAULT profile so that general users cannot maintain user profiles.


REV00111 No storage available to start report
Explanation

A request to start a report has failed due to insufficient storage. This is probably because of other reports that are using most or all of the storage allocated to Adabas Review.

Action

Purge one of the already existing reports or try again later.


REV00116 Statistics profile was not saved
Explanation

The statistics profile was not saved.

Action

This message is for information only.


REV00120 Users attached for test simulation
Explanation

This confirms that users have been attached to simulate a load on Com-plete.

Action

This message is for information only.


REV00121 Error error-number attaching users
Explanation

An error has occurred while trying to attach users for load simulation.

Action

If the problem reoccurs, contact your Software AG technical support representative.


REV00123 Statistics profile has been saved
Explanation

The statistics profile has been saved.

Action

This message is for information only.


REV00124 TID number must be numeric
Explanation

A TID number was entered into the SA screen via the T= or TID= command but is was not numeric.

Action

Enter a numeric TID number.


REV00125 Report definition has been saved successfully
Explanation

This confirms that the request to save a report definition was successful.

Action

This message is for information only.


REV00129 Report definition not found
Explanation

An attempt was made to retrieve a report definition but no report definition by that name was found.

Action

Determine the correct name or create a new definition.


REV00132 Interval may not be greater than 1440 minutes
Explanation

The interval may not be greater than 1440 minutes.

Action

This message is for information only.


REV00133 Review is terminating
Explanation

A request was made to start, view, or list a report, but Adabas Review is in the process of terminating.

Action

This message is for information only.


REV00134 Duplicate report name - report not started
Explanation

An attempt to start an Adabas report has failed because a report with the same name is already active.

Action

Purge the currently active report and retry or start a report with a different name.


REV00135 Review command not provided
Explanation

An attempt was made to communicate with the Adabas Review exit but no Adabas Review command was provided.

Action

Provide an Adabas Review command.


REV00137 Insufficient storage to issue Review command
Explanation

The Adabas Review exit routine is not accepting communications due to insufficient storage.

Action

Purge at least one of the started reports.


REV00138 Insufficient storage to start report
Explanation

An attempt to start an Adabas Review report has failed due to insufficient storage.

Action

Purge an active report and retry.


REV00139 Invalid SUMMARY, MAX or MIN field
Explanation

An attempt to start an Adabas Review report has failed because fields were marked as Sum, Min, Max, or Avg, but these fields are only allowed to be Order fields.

Action

Make the fields Order fields only.


REV00140 An invalid value was specified in the RULE
Explanation

An attempt to start an Adabas Review report has failed because values specified in the Rule where either too long, or in case of numbers with a decimal point, the formatting is not correct.

Action

Specify a correct value in the RULE.


REV00141 Format buffer error
Explanation

A format buffer error has occurred while trying to communicate with the Adabas Review exit routine.

Action

Contact your Software AG technical support representative.


REV00144 Display program not found
Explanation

An attempt to view an active report has failed because the display program for this report cannot be found.

Action

Generate a display program by resaving the report definition, if it is available, or change the display program name on the LS screen to a program name that is known to be acceptable for this report.


REV00145 Natural error: error-number
Explanation

A Natural error condition occurred. The Natural error message number is displayed.

Action

Reference the Natural online message utility for an explanation of the error.


REV00146 Report definition was not saved
Explanation

The request to save a report definition was canceled by the user in response to an overlay warning.

Action

This message is for information only.


REV00147 Too many fields - exceeds max linesize - save canceled
Explanation

The request to save a report definition was canceled because the resulting generated display program would have exceeded the maximum allowable line size.

Action

Reduce the number of fields and try again.


REV00148 DBID has been changed
Explanation

This confirms that the request to change the target DBID was successful.

Action

This message is for information only.


REV00149 There are no started reports
Explanation

A request to list started reports was made but there are no started reports to list.

Action

This message is for information only.


REV00150 Detailed reports cannot be viewed online
Explanation

Only summary reports can be viewed online. Detailed reports are printed at Adabas termination time.

Action

This message is for information only.


REV00151 Insufficient storage to reactivate report
Explanation

An attempt was made to reactivate a report that was deactivated by Adabas Review due to insufficient storage. The report cannot be reactivated.

Action

Use the refresh (RF) command to purge the existing data and start accumulating new information.


REV00152 Report has been refreshed
Explanation

This confirms that a refresh (RF) command was successful.

Action

This message is for information only.


REV00153 There are no history reports
Explanation

A request to List History Reports was canceled because there are no history reports to list.

Action

This message is for information only.


REV00155 DBID must be between 0 and 255.
Explanation

An attempt was made to change the DBID number to less than 0 or greater than 255.

Action

Enter a DBID number in the range of 0 to 255.


REV00156 Invalid AND/OR field
Explanation

A value other than AND or OR was entered into the AND/OR field of the selection criteria on the Processing Rules screen.

Action

Enter AND or OR.


REV00157 No field specified
Explanation

No field name was specified for the entered criteria on the Edit Report screen.

Action

Enter a field name.


REV00158 AND/OR field not followed by another condition
Explanation

AND or OR was entered into the AND/OR field of the Processing Rules screen but no condition followed.

Action

Either remove the AND/OR or enter another condition.


REV00159 AND/OR field missing
Explanation

More than one condition was coded on the Processing Rules screen, but no AND/OR was coded for the previous condition.

Action

Enter AND/OR on the previous condition


REV00160 OPERATOR field missing
Explanation

The OPERATOR field has been left blank on a condition.

Action

Fill in the OPERATOR field.


REV00161 VALUE field missing
Explanation

The VALUE field has been left blank on a condition.

Action

Fill in the VALUE field.


REV00162 Invalid OPERATOR field
Explanation

An invalid operator was entered into the OPERATOR field of the Processing Rules screen.

Action

Enter a valid operator.


REV00163 Invalid field name
Explanation

An invalid field name was entered on the Edit Report screen.

Action

Press PF11 for a list of valid field names.


REV00169 ORDER number too high
Explanation

A number greater than 20 was entered into the ORDER field of the Edit Report screen. 20 is the highest number that can be entered.

Action

Enter a number between 1 and 20.


REV00170 field-name is not a valid field for SUM, AVG, PCT or ROUND
Explanation

A field was marked for SUM, AVG, PCT, or ROUND on the Edit Report screen, but the field marked is not a numeric field. Fields must have a numeric output to be eligible for SUM, AVG, PCT, or ROUND.

Action

Place a number in the ORDER column, and remove any marks for SUM, AVG, PCT, or ROUND.


REV00171 SAVE/START canceled by operator
Explanation

The request to save a report definition was canceled by the user in response to an overlay warning.

Action

This message is for information only.


REV00175 Invalid value
Explanation

An invalid value was entered as part of a logical condition on the Edit Report screen.

Action

Enter a valid value.


REV00176 Internal storage error
Explanation

An internal storage management error has occurred within the Adabas Review nucleus.

Action

If the problem recurs, contact your Software AG technical support representative.


REV0017 ROUND is only valid on fields with an ORDER number
Explanation

A rounding factor was specified for a field that does not also have an order number specified.

Action

Enter a number in the ORDER field, or remove the rounding factor.


REV00179 You must enter ORDER, SUM, MIN, MAX, PCT or AVG
Explanation

A field was entered on the Edit Report screen but no action was specified; i.e. ORDER, SUM, MIN, MAX, PCT, or AVG.

Action

Enter a number in the ORDER field and/or an X in one or more of the SUM, MIN, MAX, PCT, or AVG fields


REV00180 Invalid data in ROUND column
Explanation

The data entered into the round column of the Edit Report screen was not numeric.

Action

Enter a number with or without a decimal into the round field.


REV00181 ADACALL must be an integer between 0 and 32,767
Explanation

ADACALL specifies the maximum number of Adabas calls an application can make before the Com-plete / Adabas interface forces the application to be rolled out. This parameter is ignored if ADAROLL=NO is specified.

Action

Enter a number between 0 and 32,767.


REV00182 ADALIMIT must be an integer between 0 and 32,767
Explanation

ADALIMIT specifies the number of Adabas calls that many be made by an online transaction without any intervening terminal I/O. Programs that exceed this limit are canceled.

Action

Enter a number between 0 and 32,767.


REV00183 ADAROLL must be 'ALWAYS', 'NEVER', or less than 30.99
Explanation

ADAROLL specifies the amount of time Com-plete will wait for Adabas calls before rolling out the program making the call.

Action

Enter ALWAYS, NEVER, or a number less than 30.99.


REV00184 ADACALL for DBID dbid has been changed to yyyyy by user-id
Explanation

The ADACALL parameter for the specified database was changed to yyyyy through the facilities provided by the Adabas Communication Statistics function (Adabas Calls from Com-plete) in Adabas Review DC.

Action

This message is for information only.


REV00185 ADALIMIT for DBID dbid has been changed to yyyyy by user-id
Explanation

The ADALIMIT parameter for the specified database was changed to yyyyy through the facilities provided by the Adabas Communication Statistics function (Adabas Calls from Com-plete) in Adabas Review DC.

Action

This message is for information only.


REV00187 Only 'Y' and 'N' are valid values
Explanation

The letter "Y" (yes) and the letter "N" (no) are the only two valid values for this field.

Action

Enter "Y" if you wish the APPLYMOD to be active; or enter "N" if you wish to deactivate the applymod.


REV00188 The ADABAS/COM-PLETE parameters have been updated
Explanation

This message confirms that the Adabas / Com-plete parameters have been successfully updated.

Action

This message is for information only.


REV00190 Invalid cursor placement for requested function
Explanation

The cursor must be placed on a line that contains valid data.

Action

Place cursor on a line with valid data.


REV00193 Too many xxx fields
Explanation

xxx is ORDER, SUM, MIN, MAX, AVG, or ROUND. There were too many of the indicated fields to process. When all field names are combined, they will not fit into an 80-byte statement. The 80-byte statements are used internally by Adabas Review for report definition storage.

Action

Reduce the number of fields by one until the message disappears.


REV00195 Invalid page number entered
Explanation

A number was entered on the Adabas Review command line that was greater than the actual number of pages available.

Action

Enter a valid page number.


REV00196 Roll buffer not allocated
Explanation

The roll buffer is not allocated.

Action

This message is for information only.


REV00197 Roll data sets not allocated
Explanation

The roll data sets are not allocated.

Action

This message is for information only.


REV00198 User not logged on
Explanation

The user is not logged on.

Action

This message is for information only.


REV00199 Invalid wrap option
Explanation

An invalid wrap option was specified in the report definition. The option must be NONE, STD, or HIGH.

Action

This message is for information only.


REV00200 Low water mark must be less than high water mark
Explanation

The low water mark specified was higher than or equal to the high water mark.

Action

Enter a number less than the high water mark.


REV00202 Review is not installed in database dbid
Explanation

An attempt was made to either start a report or to list started reports against a database that either does not have Adabas Review installed as a user exit 4 or does not currently have LOGGING turned on.

Action

Verify that Adabas Review is installed on the target DBID. If it is, ensure that ADARUN LOGGING=YES has been specified and that LOGGING has not been subsequently disabled from the operator console.


REV00203 Report hard copy has been queued
Explanation

This confirms that a request to send report output to a hardcopy device completed successfully, and that the report is either now printing or has been placed on the queue to be printed.

Action

This message is for information only.


REV00205 Invalid display program name
Explanation

An attempt was made to change the display program name using the CP command of the List Reports screen, but the new name is blank or invalid.

Action

Enter a valid program name.


REV00206 Display program name has been changed
Explanation

This confirms that the request to change the display program name using the CP command of the List Report Definitions screen was successful.

Action

This message is for information only.


REV00207 Report definition was purged by another user
Explanation

The report definition selected is being purged by another user.

Action

This message is for information only.


REV00209 Invalid character in report name
Explanation

An invalid character such as a quotation mark or a period was used as part of the report name.

Action

Remove the invalid character from the report name.


REV00210 Invalid start/stop date
Explanation

A date range was entered for viewing a history report but the date(s) are not valid. This may mean that the starting date is greater than the ending date, or that invalid numeric data or an invalid date format has been entered.

Action

Enter a valid date range in the form of yyyy-mm-dd or press ENTER to default to the maximum date range.


REV00211 History reports must be purged from the expanded list
Explanation

An attempt was made to purge a history report from the LH screen. This is not a valid LH function. The list must be expanded using the EX command before history reports can be purged.

Action

Enter EX in the SEL column next to the report to be purged. An expanded list will appear from which the Purge History Report (PH) function can be executed.


REV00212 Enter date range
Explanation

This prompts you to enter a date range before viewing a history report. The maximum date range (all dates) is the default.

Action

Enter a date range in the form of yyyy-mm-dd, or press ENTER to default to the maximum date range.


REV00214 Display program regeneration complete
Explanation

The request to regenerate display programs has completed successfully.

Action

This message is for information only.


REV00217 Review system file not available
Explanation

Adabas Review attempted to read information from its system file but received an Adabas response code of 148 (ADARSP148).

Action

Bring up the database that has the Adabas Review repository and make sure that the LFILE parameter has been specified correctly.


REV00218 Default system must be 'DB', 'DC', 'MM', or 'NM'
Explanation

An invalid value was entered for default system. The valid system codes are:

DB Database (Adabas Review)
DC Data Communication
MM Main Menu
NM Natural Monitor
Action

Enter a valid system code.


REV00219 Input not numeric
Explanation

A value was entered into a field that is intended to accept numeric data only.

Action

Enter a valid numeric value.


REV00220 Auto regenerate started
Explanation

The subtask to generate auto-report definitions was successfully started.

Action

This message is for information only.


REV00221 Auto regenerate already active
Explanation

The subtask to generate auto-report definitions is still active from a previous execution.

Action

Wait a few seconds and try the command again.


REV00222 Auto regenerate failed
Explanation

The subtask to regenerate auto-report definitions was not attached and did not run.

Action

Check your Adabas STEPLIB and make certain that the module RAOSAUTO is present.


REV00223 UEX4 version error
Explanation

The Adabas UEX4 module RAOSEXIT is not the correct version.

Action

Verify that Adabas Review has been correctly installed.


REV00224 MSG function not available from this screen
Explanation

The Adabas Review message help subsystem is not available from this screen.

Action

Perform the MSG function from another screen.


REV00225 DBID must be between 1 and 65535
Explanation

The target database ID must be in the range between 1 and 65535.

Action

Enter a database ID in the specified range.


REV00226 SVC is zero
Explanation

The SVC specified cannot be zero (0).

Action

Enter a correct SVC number.


REV00227 Target type must be 'ADA', 'NET', 'NPR', or 'TPF'
Explanation

The target type must be one of the specified values.

Action

Enter the correct target type.


REV00228 DBID for Adabas target type must be less than 255
Explanation

If the target type is ADA, then the target database ID must be in the range of 1 to 255.

Action

Enter a database ID in the specified range.


REV00229 Field value must be 'Y' or 'N'
Explanation

An invalid value was entered for the field.

Action

Enter a valid field value: either yes ("Y") or no ("N").


REV00230 No target definition found for target target-id
Explanation

The target definition did not exist for the requested target.

Action

Define the target.


REV00231 Target definition for DBID dbid saved
Explanation

The target definition was successfully saved.

Action

This message is for information only.


REV00234 Default definition cannot be purged
Explanation

The default definition for target 00000 cannot be purged.

Action

This message is for information only.


REV00235 Target definition(s) purged successfully
Explanation

The target definitions marked for purge were successfully deleted.

Action

This message is for information only.


REV00236 No target definition exists for DBID dbid and default is not present
Explanation

The target definition for the database specified did not exist, and there was also no default definition.

Action

Add the target definition for the specified target.


REV00237 Generate started
Explanation

The subtask to generate report definitions was successfully started.

Action

This message is for information only.


REV00238 Generate already active
Explanation

The subtask to generate report definitions is still active from a previous execution.

Action

Wait a few seconds and try the command again.


REV00239 Generate failed
Explanation

The subtask to generate report definitions was not attached and did not run.

Action

Check your Adabas STEPLIB and make certain that the module RAOSAUTO is present.


REV00240 Function canceled
Explanation

The requested function was terminated by user request and was not performed.

Action

This message is for information only.


REV00241 Review file set successfully
Explanation

The Adabas Review data file's database ID and file number were set successfully.

Action

This message is for information only.


REV00242 Unable to open command log file for output
Explanation

A report was started with the logging option set to "Y" (yes), but the file specified for output cannot be opened. The report is started without logging.

Action

If this is an online report, make sure the DSN field of the Report Options screen is set to a valid command log output file. If this is a batch report, make sure the DSN= parameter of the LOG statement is set to a valid command log output file.


REV00243 Adabas Online Services is not installed
Explanation

The request to invoke Adabas Online System (AOS) from Adabas Review has failed because AOS is not installed in the current Natural system file.

Action

This message is for information only.


REV00244 Components not installed properly
Explanation

The installation process did not complete successfully.

Action

Make sure that all INPL and IUPD media are properly installed.


REV00245 PFnn not defined
Explanation

The PF key that was pressed is not defined to perform a function.

Action

Press a valid PF key.


REV00246 Press 'PF3' to exit or 'PF5' to save the profile
Explanation

To exit without saving the changes made to a user profile, press PF3. To save the changes made to a user profile, press PF5.

Action

See explanation.


REV00247 Userid must be specified
Explanation

A user ID must be specified.

Action

Enter a user ID.


REV00248 Natural error error-number has occurred on line line-number of program program-name
Explanation

A Natural error has occurred in one of Adabas Review's programs.

Action

Record the information given in the message and contact your Software AG technical support representative.


REV00249 Command log data set already in use
Explanation

A report was started with the logging option set to "Y" (yes), but the specified output data set is already in use by another report. The report is started without logging.

Action

Either use another data set, or purge the report that is using the command log data set.


REV00250 Logging is not valid for summary reports
Explanation

LOGGING was specified on the Report Options screen for a summary report. Only detail reports can perform the LOGGING function.

Action

Either set LOGGING to "N" or set SUM/DETAIL to "D".


REV00252 At least one field is required
Explanation

An attempt was made to save a report definition with no fields to be displayed. At least one field is required to save a report.

Action

Correct the report definition and press PF5to save the report definition.


REV00253 There are no report definitions on file
Explanation

A request to list report definitions cannot be satisfied because there are no definitions to list.

Action

This message is for information only.


REV00254 At least one order field is required
Explanation

An attempt to save a summary report failed because there are no ORDER fields. At least one ORDER field is required for summary reports.

Action

Make at least one field an ORDER field and save the report.


REV00255 Report definition conversion complete
Explanation

The process of converting Adabas Review report definitions has completed.

Action

This message is for information only.


REV00256 History file conversion complete
Explanation

The process of converting Adabas Review history reports completed.

Action

This message is for information only.


REV00257 User profile conversion complete
Explanation

The process of converting Adabas Review user profiles has completed.

Action

This message is for information only.


REV00258 Report definition conversion was canceled
Explanation

The process of converting Adabas Review report definitions was canceled at the request of the user. Any reply other than "yes" or "change" on the LFILE confirmation screen will cause this message.

Action

This message is for information only.


REV00259 History file conversion was canceled
Explanation

The process of converting Adabas Review history reports was canceled at the request of the user. Any reply other than "yes" or "change" on the LFILE confirmation screen will cause this message.

Action

This message is for information only.


REV00260 User profile conversion was canceled
Explanation

The process of converting Adabas Review user profiles was canceled at the request of the user. Any reply other than "yes" or "change" on the LFILE confirmation screen will cause this message.

Action

This message is for information only.


REV00261 There are no report definitions to convert
Explanation

An attempt was made to convert report definitions, but there are none to convert. Adabas Review only converts report definitions that do not already exist in the target Adabas Review repository.

Action

This message is for information only.


REV00262 There are no history reports to convert
Explanation

An attempt was made to convert Adabas Review history reports, but there are none to convert.

Action

This message is for information only.


REV00263 There are no user profiles to convert
Explanation

An attempt was made to convert Adabas Review user profiles, but there are none to convert. Adabas Review only converts user profiles that do not already exist in the target Adabas Review repository.

Action

This message is for information only.


REV00264 Error error-number while trying to convert report definitions
Explanation

Either an Adabas or a Natural error has occurred while trying to convert report definitions.

Action

Follow the Adabas or Natural procedures for error correction.


REV00265 Error error-number while trying to convert history reports
Explanation

Either an Adabas or a Natural error has occurred while trying to convert history reports.

Action

Follow the Adabas or Natural procedures for error correction.


REV00266 Error error-number while trying to convert user profiles
Explanation

Either an Adabas or a Natural error occurred while trying to convert user profiles.

Action

Follow the Adabas or Natural procedures for error correction.


REV00267 Do not try to convert to and from the same file
Explanation

An attempt was made to run an Adabas Review conversion program with identical TO and FROM files.

Action

Correct the LFILE for the TO or FROM file.


REV00268 Invalid file number
Explanation

The user attempted to change the database ID and file number of the Adabas Review repository. The file number specified was not an Adabas Review file.

Action

Specify a correct Adabas Review DBID/file number.


REV00269 No active targets found on SVC svc
Explanation

No active database targets were found on the SVC number specified in the message.

Action

Verify that the target definitions are defined to the correct SVC number.


REV00270 Database dbid is a Natural Process target
Explanation

The target selected is an Entire System Server (formerly Natural Process) target type.

Action

This message is for information only.


REV00271 Database dbid is not active
Explanation

The database selected is not active.

Action

This message is for information only.


REV00272 Database dbid is a non-Adabas target
Explanation

The database selected is a non-Adabas type target.

Action

This message is for information only.


REV00273 Report is already suspended
Explanation

An attempt was made to suspend a report that was is already suspended.

Action

This message is for information only.


REV00274 Invalid OP summary option
Explanation

An invalid option was entered on the Edit Report screen for the OP summary parameter.

Action

Enter a valid option.


REV00275 New report definition
Explanation

A new report definition is being created.

Action

Enter the parameters for the new report definition or exit.


REV00276 Report is already active
Explanation

An attempt was made to reactivate a report that was already active.

Action

This message is for information only.


REV00277 History data has been purged
Explanation

Historical data was purged.

Action

This message is for information only.


REV00278 History data was not purged
Explanation

Historical data was not purged.

Action

This message is for information only.


REV00279 History data not found
Explanation

Historical data was not found.

Action

This message is for information only.


REV00280 Available storage in thread insufficient
Explanation

The available storage in the thread is insufficient.

Action

Contact your Software AG technical support representative.


REV00281 An invalid request or an invalid FQE was found
Explanation

An invalid request or an invalid free queue element (FQE) was found.

Action

Contact your Software AG technical support representative.


REV00282 No response time report definition was specified
Explanation

No response time report definition was specified.

Action

Contact your Software AG technical support representative.


REV00283 Report definition has been purged
Explanation

Report definition has been purged.

Action

This message is for information only.


REV00284 Report definition was not purged
Explanation

Report definition was not purged.

Action

This message is for information only.


REV00285 Invalid device type for download
Explanation

An attempt was made to download a report but the Natural session is not in PC mode.

Action

If the device is a PC using Entire Connection, set your Natural session to PC mode by entering %+ on the command line, and reenter the DL command.


REV00286 Duplicate order numbers
Explanation

More than one field has the same order number on the Edit Report screen.

Action

Make each order number unique.


REV00288 Report is not active
Explanation

An attempt was made to perform a function on a started report, but no started report with the specified report name was found.

Action

This message is for information only.


REV00289 LOG command not allowed while viewing data
Explanation

An attempt was made to issue the LOG command while viewing a report.

Action

Stop viewing the report and reissue the LOG command.


REV00290 Adabas Review logging status changed
Explanation

The Adabas Review dynamic logging options have been updated.

Action

This message is for information only.


REV00291 Error returned during LOG request - nnnn
Explanation

The LOG command was issued and an error occurred during processing. nnnn = the response code associated with the error.

Action

Follow the Adabas or Natural procedures for error correction.


REV00292 Review not installed on database
Explanation

While attempting to view the buffer pool display, Adabas determined that Adabas Review was not installed on that database and issued a response code.

Action

This message is for information only.


REV00293 Function restarted due to Adabas rsp code 9
Explanation

An Adabas Review function was restarted from the beginning because an Adabas response code 9 (ADARSP009) was received.

Action

This message is for information only.


REV00294 NM component not installed
Explanation

An attempt was made to enter Adabas Review NM, but the NM component was not on the installation media.

Action

Determine whether the NM component was actually purchased. If it was purchased, then you may have inadvertently received the wrong Adabas Review installation media. Contact your Software AG representative.


REV00295 Select a history report
Explanation

An attempt was made to view a list of dates and times of history records for a response time report without specifying the name of the report.

Action

Specify the response time name.


REV00296 TID must be between 1 and 65,535
Explanation

The terminal ID (TID) must be between 1 and 65,535.

Action

Enter a valid TID number.


REV00297 Invalid TID specified
Explanation

An invalid terminal ID (TID) was specified.

Action

Enter a valid TID number.


REV00299 Function has been discontinued
Explanation

The current version of Adabas Review no longer supports the requested function.

Action

Refer to the Adabas Review User documentation for a list of available features and functions.


REV00300 Report not on file
Explanation

The requested report definition could not be found in the Adabas Review data file.

Action

This message is for information only.


REV00301 No OP summary information available
Explanation

No OP summary information was available for the report specified.

Action

This message is for information only.


REV00306 First field cannot be a buffer segment
Explanation

A DB report was defined with the first field as a buffer segment (FBSEG01, RBSEG01 ETC). The first field cannot be a buffer segment.

Action

Make another field the first field.


REV00307 No resident PGMLIB defined
Explanation

A request was made to view a list of programs in the resident program library buffer, but none were defined to Com-plete.

Action

This message is for information only.


REV00308 No resident programs defined
Explanation

A request was made to view a list of programs in the resident programs, but none where defined to Com-plete.

Action

This message is for information only.


REV00309 Unable to locate Adabas IDTH
Explanation

Adabas Review was unable to locate the Adabas IDT header.

Action

Contact your Software AG technical support representative.


REV00310 Unable to load ADALDI
Explanation

Adabas Review was unable to load the ADALDI text module from the Adabas TXTLIB.

Action

Verify that the Adabas TXTLIB is accessible from your z/VM machine.


REV00311 Database dbid has been ignored
Explanation

The specified database has been ignored because an entry for the DBID was found in the IGNORE table in program N-IGNORE. No STATUS information is returned for this database.

Action

If STATUS information for the database should be returned, edit and STOW the program N-IGNORE.


REV00312 Insufficient storage to reset stopwatch
Explanation

An attempt to reset the stopwatch was unsuccessful due to insufficient storage.

Action

Try again later.


REV00313 Only 'ON' and 'OFF' are valid values
Explanation

A value other than ON or OFF was entered.

Action

Enter ON or OFF.


REV00314 Command log data set switched
Explanation

The command log data set was switched successfully.

Action

This message is for information only.


REV00315 Command logging is not active for report
Explanation

Adabas Review command logging is not active for the specified report.

Action

Choose a report that has command logging.


REV00316 Invalid subpool ID
Explanation

The subpool ID specified was invalid.

Action

Select a valid subpool.


REV00317 There are no transaction summary records
Explanation

A Response Time Report was requested but no transaction summary records exist for the selected report.

Action

This message is for information only.


REV00318 There are no OP summary records
Explanation

A Response Time Report was requested but no OP summary records exist for the selected report.

Action

This message is for information only.


REV00319 Too many "AND" fields in selection criteria
Explanation

The AND fields in the selection criteria have resulted in a data string that is too long for Adabas Review to process.

Action

Reduce the number of AND statements and resave the report.


REV00320 Too many "OR" fields in selection criteria
Explanation

The OR fields in the selection criteria have resulted in a data string that is too long for Adabas Review to process.

Action

Reduce the number of OR statements and resave the report.


REV00321 Target SVC cannot be greater than 255
Explanation

A value larger than allowed was entered in the SVC field of the target definition. The maximum value for this field is 255.

Action

Enter the correct SVC number.


REV00322 User has already been canceled
Explanation

The user specified in the cancel function has already been canceled.

Action

This message is for information only.


REV00323 TID terminal-id canceled
Explanation

The specified terminal ID has been canceled.

Action

This message is for information only.


REV00325 TERMINAL terminal-name canceled
Explanation

The specified terminal has been canceled.

Action

This message is for information only.


REV00326 TID terminal-id not found
Explanation

The terminal ID specified in the cancel, pick, or force function could not be found.

Action

This message is for information only.


REV00327 User user-id not found
Explanation

The user specified in the cancel, pick, or force function could not be found.

Action

This message is for information only.


REV00328 Terminal terminal-name not found
Explanation

The terminal name specified in the cancel, pick, or force function could not be found.

Action

This message is for information only.


REV00329 Invalid TID specified
Explanation

The terminal ID number specified in the cancel, pick, or force function was not a valid numeric value.

Action

This message is for information only.


REV00330 Response time report - report-name STARTED
Explanation

The specified Adabas Review response time report was successfully autostarted.

Action

This message is for information only.


REV00331 No autostarted reports found to start
Explanation

No Adabas Review Response Time reports were found to autostart.

Action

This message is for information only.


REV00332 One report has been autostarted
Explanation

Adabas Review has started one autostarted response time report.

Action

This message is for information only.


REV00333 count reports have been autostarted
Explanation

Adabas Review started the specified number of autostarted response time reports.

Action

This message is for information only.


REV00334 History task recovery from Adabas time-out
Explanation

The Adabas Review history interval task successfully recovered from an Adabas timeout (response code 9, ADARSP009).

Action

This message is for information only.


REV00335 RNMH history task initializing in Natural
Explanation

The Adabas Review history interval task successfully invoked Natural and is initializing.

Action

This message is for information only.


REV00336 History task terminating. Unable to locate RNMTAB
Explanation

The Adabas Review history interval task terminated because it was unable to locate RNMTAB.

Action

Check that RNMTAB has been defined to CICS as a resident PPT entry, and that RNMTAB is available to CICS.


REV00337 History task terminating. Unable to load module-id
Explanation

The Adabas Review history interval task terminated because it was unable to locate the RNMCICS.

Action

Check that RNMCICS has been defined to CICS as a PPT entry and that RNMCICS is available to CICS.


REV00338 History task terminating. Natural error error-number detected during initialization
Explanation

The Adabas Review history interval task terminated because it encountered a Natural error during initialization.

Action

Investigate the Natural error indicated, correct the problem, and restart the history subsystem.


REV00339 History task terminating. NM data file has not been initialized
Explanation

The Adabas Review history interval task terminated because it detected that the Adabas Review Natural Monitor data file was not initialized.

Action

Verify that the INSTALL program has been executed to initialize the Adabas Review Natural Monitor data file.


REV00340 History task terminating. Non-recoverable Natural error detected
Explanation

The Adabas Review history interval task terminated because it encountered an error in Natural from which it could not recover.

Action

Investigate the Natural error indicated, correct the problem, and restart the history subsystem.


REV00341 History task terminating normally
Explanation

The Adabas Review history interval task terminated normally.

Action

This message is for information only.


REV00342 History task terminating. Maximum reinitialization counter exceeded
Explanation

The Adabas Review history interval task terminated because the counter for maximum reinitializations was exceeded.

Action

Check messages sent to Adabas Review prior to this message to determine why the history task has reinitialized so many times.


REV00343 History task terminating
Explanation

The Adabas Review history interval task terminated.

Action

Check other Adabas Review messages issued prior to this message to determine if an error condition was encountered.


REV00344 TID terminal-id canceled by user-id at terminal terminal-name
Explanation

The user with the specified terminal ID was canceled by another user at another terminal.

Action

This message is for information only.


REV00345 User user-id canceled by user-id at terminal terminal-name
Explanation

The user with the specified user ID was canceled by another user at another terminal.

Action

This message is for information only.


REV00346 Terminal terminal-name canceled by user-id at terminal terminal-name
Explanation

The terminal with the specified name was canceled by another user at another terminal.

Action

This message is for information only.


REV00347 TID terminal-id forced
Explanation

The user with the specified terminal ID was forced.

Action

This message is for information only.


REV00348 User user-id forced
Explanation

The user with the specified user ID was forced.

Action

This message is for information only.


REV00349 Terminal terminal-name forced
Explanation

The terminal with the specified name was forced.

Action

This message is for information only.


REV00350 TID terminal-id forced by user-id at terminal terminal-name
Explanation

The user with the specified terminal ID was forced by another user at another terminal.

Action

This message is for information only.


REV00351 User user-id forced by user-id at terminal terminal-name
Explanation

The user with the specified user ID was forced by another user at another terminal.

Action

This message is for information only.


REV00352 Terminal terminal-name forced by user-id at terminal terminal-name
Explanation

The terminal with the specified name was forced by another user at another terminal.

Action

This message is for information only.


REV00353 User must be canceled before force
Explanation

A CANCEL command must be issued for a user before a FORCE command can be issued.

Action

This message is for information only.


REV00354 Invalid autostart option
Explanation

An invalid response time report autostart option was specified. The value must be "Y" or "N".

Action

Specify valid value.


REV00355 Invalid history refresh option
Explanation

An invalid response time report history refresh option was specified. The value must be "Y" or "N".

Action

Specify a valid value.


REV00356 Value must be in range range-start through range-end
Explanation

The value specified is invalid for the field. Valid values are denoted by <range-start> through <range-end> in the message.

Action

Specify a valid value in the range specified.


REV00357 History task terminating. Review NM incorrectly installed
Explanation

The Adabas Review history interval task terminated because it was unable to verify that the Adabas Review Natural Monitor code was correctly linked with the Natural nucleus.

Action

Verify that the Adabas Review NM code is correctly linked with the Natural nucleus.


REV00359 Report definition has been copied
Explanation

The request to copy a report definition was successful.

Action

This message is for information only.


REV00360 Review repository not available
Explanation

An Adabas response code 148 (ADARSP148) was received while trying to store information in an Adabas Review repository.

Action

Insure that the database ID and file number are correct and that the database is available.


REV00361 Database dbid inactive or invalid. Type 'TECH' for reason
Explanation

The user attempted to perform an Adabas Review function against a database that was inactive, did not have Adabas Review installed, or was not running a compatible version of Adabas Review.

Action

From the Database System menu, type TECH to determine why the current Adabas Review database is invalid and correct the error.


REV00362 Review is not installed in database dbid
Explanation

Using the DBID= command, the user attempted to change the Adabas Review database being accessed. The database selected did not have Adabas Review installed.

Action

Verify that the database specified in the DBID= command is a valid Adabas Review database.


REV00363 Database dbid is not active
Explanation

Using the DBID= command, the user attempted to change the Adabas Review database being accessed. The database selected was not active (Adabas response code 148, ADARSP148).

Action

Verify that the database specified in the DBID= command is a valid Adabas Review database and that it is active.


REV00364 Database dbid is below Review V3.4
Explanation

Using the DBID= command, the user attempted to change the Adabas Review database being accessed. The database selected has an invalid version of Adabas Review installed.

Action

Verify that the database specified in the DBID= command is a valid Adabas Review database.


REV00365 Response code rsp received accessing DBID dbid
Explanation

Using the DBID= command, the user attempted to change the Adabas Review database being accessed. The user received the indicated response code.

Action

Verify that the database specified in the DBID= command is a valid Adabas Review database.


REV00366 TECH command only available from the DB system main menu
Explanation

The user attempted to executed the TECH command from an Adabas Review panel other than the Database System menu. The Adabas Review TECH command is only executable from the Database System menu.

Action

Execute the TECH command from the Database System menu.


REV00367 Display program does not match report
Explanation

A VIEW or VW command terminated because the display program invoked was generated for a different report.

Action

Regenerate the display program for the report that failed using the RG function of the List Reports screen.


REV00368 Parentheses are required for a list or range
Explanation

A list or range of values was entered without parentheses into a processing rule.

Action

Include the values within parentheses.


REV00369 Unpaired parentheses
Explanation

The number of opening and closing parentheses are unequal.

Action

Include a closing parentheses for each opening parentheses.


REV00370 Invalid HELP command
Explanation

An invalid command was entered into the command line of a help screen.

Action

Enter a valid command or press a valid PF key.


REV00371 GENAUTO is not available in CMS
Explanation

A GENAUTO (or GA) command was entered but is not implemented in z/VM.

Action

This message is for information only.


REV00372 Download is invalid from this screen
Explanation

DOWNLOAD (or DL) was entered from a screen where the DOWNLOAD command is invalid.

Action

Enter DL into the SEL column of the List Started Reports screen.


REV00373 MAX K must be at least n K
Explanation

The MAX K value specified in the report options must be at least 4K for z/OS and z/VSE and at least 8K for BS2000.

Action

Specify a value for MAX K that is at least the minimum.


REV00374 WRAPPING=Y only allowed on sequence reports
Explanation

The WRAPPING value can only be set to "Y" for a SUMMARY report with SEQUENCE as the first display field.

Action

Only specify WRAPPING=Y for SUMMARY reports with SEQUENCE as the first field.


REV00375 Invalid page size - must be 1-255
Explanation

The page size entered on the Report Options screen is invalid. The value must be between 1 and 255.

Action

Enter a valid page size.


REV00385 Value must be greater than 0.
Explanation

The value must be greater than 0.

Action

This message is for information only.


REV00386 FNR must be between 1 and 254
Explanation

An attempt was made to change the FNR number to less than 1 or greater than 254.

Action

Enter a FNR number in the range of 1 to 254.


REV00388 Invalid line size - must be 72-255
Explanation

The line size entered on the Report Options screen is invalid. The value must be between 72 and 255.

Action

Enter a valid line size.


REV00390 List not sorted due to excessive report data
Explanation

The expanded list of history report occurrences could not be sorted because the resulting ISN list was too large. The list is displayed unsorted.

Action

Increase the value in the LS ADARUN parameter.


REV00391 History report compression complete
Explanation

The request to compress a history report completed successfully.

Action

This message is for information only.


REV00392 File is in use by another compression process
Explanation

An attempt was made to compress a history report but another report was being compressed at the time. This message can also occur if a CH function did not complete successfully.

Action

If another report is being compressed, wait until it completes and try again. If a CH function failed, you must run the RESET function.

To run the RESET function:

  1. Enter RESET HISTORY FILE on the command line of the DB System menu.

  2. Follow the instructions on the screen.


REV00393 Compression will not be performed
Explanation

A reply of "N" was given in response to the confirmation prompt prior to compressing a history report.

Action

This message is for information only.


REV00394 History file does not need resetting
Explanation

A request to reset the history file was made but the file does not need resetting.

Action

This message is for information only.


REV00395 History file has been reset
Explanation

This confirms that the history file has been reset. This essentially unlocks the lock that was placed on the file during a CH function.

Action

None if the message says HISTORY FILE HAS BEEN RESET.

If the message also says DATA WAS LOST, restore the history file to a state prior to when the failing CH function was performed.


REV00396 Duplicate field in "AND" expression
Explanation

A logical "AND" expression contains a duplicate field name in a processing rule. When using "AND" to connect fields, each field name can be used only once per expression.

Action

Remove the duplicate field name from the expression.


REV00397 Target DBID has been changed
Explanation

The target DBID has been successfully changed for the report definition.

Action

This message is for information only.


REV00398 Bufferpool reports cannot be printed or downloaded
Explanation

The graphical bufferpool reports cannot be downloaded or printed: they may only be viewed.

Action

Use the VW command to view the report.


REV00399 AA is not available in VM/CMS
Explanation

The AA function is not available in z/VM.

Action

This message is for information only.


REV00400 Non zero response from target = nnn
Explanation

A non-zero response code was returned from the specified target.

Action

Determine why the non-zero response code occurred.


REV00401 Report defaults were saved
Explanation

The report defaults were saved successfully.

Action

No action is required for this informational message.


REV00402 No matching reports to generate
Explanation

GENAUTO was started in local mode, but there are no autostarted reports with DBID-TO-MONITOR set to the local DBID. No autostarted reports will be generated.

Action

No action is required for this informational message.


REV00403 Update completed
Explanation

The report options were updated successfully.

Action

No action is required for this informational message.


REV00404 No changes to update
Explanation

A request to update reports was unnecessary because no changes were made.

Action

No action is required for this informational message.


REV00405 Cannot start a rpt that monitors a hub
Explanation

A request to start a report was unsuccessful because the DBID-TO-MONITOR was set to the Adabas Review hub ID. Adabas Review reports can only monitor Adabas targets.

Action

Correct the report and retry.


REV00406 Only one buffer segment allowed per report
Explanation

More than one buffer segment was defined in a report. Only one buffer segment per report is allowed.

Action

Correct the report and retry.


REV00407 There are no history records to convert
Explanation

An attempt was made to convert history records, but there are no history records to convert.

Action

No action is required for this informational message.


REV00408 Only 1 order field allowed with sum exit
Explanation

A summary exit was specified, but more than one order field was chosen for the report. Summary exit reports are limited to one (1) order field.

Action

Reduce the number of order fields to 1.


REV00409 Pulse report cannot be purged
Explanation

A request was made to purge the Pulse report. The Pulse report cannot be purged.

Action

No action is required for this informational message.


REV00410 Report defaults not saved
Explanation

A user canceled a prompt to confirm the saving of report defaults.

Action

No action is required for this informational message.


REV00411 xxxxxxxx cannot be edited
Explanation

The EP command was used to edit a display program, but the display program is for a fixed format report. Since these programs are specific, not dynamic, no source code is available to the user.

Action

No action is required for this informational message.


REV00412 NUCID nnnnn is not available
Explanation

An attempt was made to change the nucleus ID with which Adabas Review communicates, but the requested nucleus ID was not available.

Action

Enter the NUC LIST command to obtain a list of available nucleus IDs and try again.


REV00413 NUCID only valid for cluster databases
Explanation

A user executed the NUCID or NUC LIST command for a non-cluster database.

Action

No action is required for this informational message.


REV00414 Duplicate field names not allowed
Explanation

Two or more fields with the same name were entered on the ER screen. This is not allowed.

Action

Remove the duplicate fields.


REV00415 Detail printer not available
Explanation

A request to start a detail report failed because there was no detail printer available.

Action

Delete another detail report first or provide more printers in the startup JCL. Then try again.


REV00416 Invalid data in rules value
Explanation

An invalid character was entered into a processing rules value.

Action

Remove the invalid character from the rules value and try again.


REV00417 Pulse interval must not be greater than 1440
Explanation

The pulse interval was incorrectly specified for a Pulse report.

Action

Specify a value between 1 and 1440 and try again.


REV00418 Display program is not delivered in source form
Explanation

An attempt to edit the display program BUFFPOOL, PU-00001 or CS-00001 failed because it is not delivered as source.

Action

No action is required for this informational message.


REV00419 List size exceeded
Explanation

The maximum list size of 10 has been exceeded in a processing rule.

Action

Limit the list size to 10 and try again.


REV00420 Unable to obtain SVC list
Explanation

An AA command was issued, but the list of SVCs cannot be accessed.

Action

Make certain that ADATMZ exists and is accessible from the current Adabas Review hub or database. Then try again.


REV00421 There are no targets for this SVC
Explanation

After an AA command, an SVC was selected, but there are not targets available for that SVC.

Action

No action is required for this informational message.


REV00422 Only order fields are allowed for detailed reports
Explanation

SUM, MIN, MAX, AVG, or ROUND were selected on the Edit Reports screen, but the report is a detailed report. ORDER is the only valid entry for a detailed report.

Action

Remove the invalid entries and try again.


REV00423 Report type changed -- defaults were reset
Explanation

While editing a report, the detail/summary report type was changed. Each report type requires its own set of default report options. The default report options for the new report type have now been loaded.

Action

No action is required for this informational message. Press PF2 to make any necessary changes to the report options.


REV00424 Unable to retrieve data from target nnnnn
Explanation

For reasons unknown to Adabas Review, the requested target was unable to supply AA information.

Action

No action is required for this informational message.


REV00425 Parameter input is missing or invalid
Explanation

The expected parameter input was either missing or has invalid data.

Action

Correct the input data and try again.


REV00426 Value for keyword is missing or invalid.
Explanation

The parameter input for a keyword was either missing or has invalid data.

Action

Correct the keyword input and try again.


REV00427 {TARGET|DBID|FILE} is not available
Explanation

The parameter input for a SET command keyword refers to an unavailable destination.

Action

Correct the keyword data or make sure the destination is available.


REV00428 {TARGET ID|DBID|FILE} has been set to nnnnn
Explanation

A SET command changed the target ID, database ID, or file successfully.

Action

No action is required for this informational message.


REV00429 SET program has terminated with errors
Explanation

The SET program encountered errors. The error will have been more clearly identified in a previous message.

Action

Correct the error and try again.


REV00430 More than 256 target definitions on file
Explanation

The maximum number of target definitions has been exceeded.

Action

Limit the number of targets to 256.


REV00431 Cannot save report due to error
Explanation

An attempt to save a report was unsuccessful because there was an error in the report definition.

Action

Correct the report definition and try again.


REV00432 There are no REVIEW hubs running on SVC nnn
Explanation

The AH (Available Review Hubs) command was entered but there are no hubs running in the current SVC to display.

Action

No action is required for this informational message.


REV00433 ADATMZ cannot be loaded
Explanation

Upon initialization, SYSREVDB calls a program named ADATMZ. This program was not available.

Action

Make certain ADATMZ is installed and available to SYSREVDB. If you are running Adabas Review in a CICS environment, verify that ACITMZ is installed. For more information, read the Adabas Review installation documentation.

If the problem persists, contact your Software AG technical support representative.


REV00434 ADATMZ: message-text
Explanation

Upon initialization, SYSREVDB calls a program named ADATMZ. One of the following messages (message-text) is included in the message and describes the error that has occurred with ADATMZ.

Message Text Explanation Action
No Adabas SVCs found An internal error has occurred. Contact your Software AG technical support representative for assistance.
No active targets for an SVC
IDTHE appears to be invalid
Invalid or unknown function
Caller has answer area no answer count
GETMAIN for SVC table failed
GETMAIN for target table failed
Load of link routine failed ADATMZ dynamically loads ADALNKR. If ADALNKR cannot be loaded, subsequent calls to ADATMZ can cause this problem. Be sure that the ADATMZ and ADALNKR modules, which are available in the Adabas or WAL load libraries, are all available for the TP monitor.
Load of CCSTCK routine failed ADATMZ dynamically loads CCSTCK. If CCSTCK cannot be loaded, subsequent calls to ADATMZ can cause this problem. Be sure that the ADATMZ and CCSTCK modules, which are available in the Adabas or WAL load libraries, are all available for the TP monitor.
Initialization call to DEPRTR failed An internal error has occurred. Contact your Software AG technical support representative for assistance.
No SVC table address provided by caller
SVC table address inconsistent with PAL
No SVC count provided by caller
Invalid SVC number too low The version of ADATMZ that was loaded is too low. Install the current version of ADATMZ. Contact your Software AG technical support representative for assistance.
Invalid SVC number too high The version of ADATMZ that was loaded is too high. Install the current version of ADATMZ. Contact your Software AG technical support representative for assistance.
No SVC tbladdr on get target call An internal error has occurred. Contact your Software AG technical support representative for assistance.
No target tbladdr on get target call
No target table length

REV00435 Buffer Pool reports cannot have DBID=ALL
Explanation

A value of "ALL" was specified as the DBID to monitor while attempting to start a report. Buffer Pool reports must only collect data from a single database, specifying "ALL" for them is not allowed. The report will not be started.

Action

Specify a numeric DBID for the Buffer Pool report.


REV00436 Invalid field for client report
Explanation

A reporting field was referenced in a client report that was not valid for client reports. Client reports have a restricted set of available fields. A complete list of these fields is provided in ????

Action

Specify a valid field name.


REV00437 The maximum number of fields has been selected
Explanation

While selecting fields for a report using the online field selection screens, the maximum allowable number of fields you can select has been reached. All fields selected beyond the maximum are ignored.

Action

Specify fewer fields, ensuring that only the most important fields are selected.


REV00438 Invalid field for a database report
Explanation

A client reporting field was referenced in a database report. This field is only permitted in a client report.

Action

Specify a valid field name.


REV00439 Warning: A client report has been started.
If client monitoring is not turned on,
no client monitoring will be collected.
Press ENTER to exit
Explanation

This message appears in a pop-up box whenever a client report is started. It warns you that if client reporting has not been started, no client reporting data will be collected.

Action

No action is required for this informational message. Press the ENTER key to remove the pop-up box containing the message.


REV00440 Redisplay buffer full - Redisplay unavailable
Explanation

The Redisplay function is unavailable because more than 5000 lines were displayed.

Action

As a workaround, the report data can be printed using the HC command and other tools might be used to scroll through that output.


REV00441 Report name cannot be 'ALL'
Explanation

The name "ALL" was used as a report name in the report definition editor. The word "ALL" is reserved in Adabas Review and cannot be used as a report name.

Action

Specify a different name.


REV00442 The display program has not been generated yet
Explanation

An attempt was made to edit the display program for a report but the display program has not yet been generated. This is most likely due to having copied a report where the display program name shows as "NEED RG" or "NEED RU".

Action

Enter RG or RU on the command line to generate the display program.


REV00443 Userid is required
Explanation

User profiles require a unique user or group ID in the User ID / Group ID field. You cannot create a user profile without one.

Action

Specify a valid user or group ID for the user profile. Valid user or group IDs are eight alphanumeric characters long and begin with either a letter or a national ($, @, or #) character.


REV00444 Group must be "Y" or "N"
Explanation

The setting for the Group access rule in the user profile definition is not "Y" (yes) or "N" (no). These are the only valid values for the field.

Action

Specify either "Y" or "N" for the Group access rule.


REV00445 Description is required
Explanation

User profiles require a description in the Description field.

Action

Specify up to 20 alphanumeric characters for the description.


REV00446 At least one report type must be "Y" for "EDIT REPORTS=Y"
Explanation

When the Edit Reports? access rule in a profile is set to "Y", at least one of the other edit report access rules must also be set to "Y". The other edit report access rules are Edit Bufferpool Reports?, Edit Client Reports?, Edit Cluster Reports?, Edit Database Reports?, and Edit Pulse Reports?.

Action

Either set the Edit Reports? access rule to "N" or specify "Y" for one of the other edit report access rules.


REV00447 All report types must be "N" for "EDIT REPORTS=N"'
Explanation

When the Edit Reports? access rule in a profile is set to "N", none of the other edit report access rules may be set to "Y". The other edit report access rules are Edit Bufferpool Reports?, Edit Client Reports?, Edit Cluster Reports?, Edit Database Reports?, and Edit Pulse Reports?.

Action

Either set the Edit Reports? access rule to "Y" or specify "N" for all of the other edit report access rules.


REV00448 Cannot save - This is the only Administrator profile
Explanation

An attempt has been made to alter and save the only administrator profile so that it is no longer an administrator profile. Adabas Review will not allow you to turn the default profile or any administrator profile into a non-administrator profile if another administrator profile is not available.

Action

If you intend to change the only administrator profile to a non-administrator profile, first create another administrator profile. You can then alter and save the original administrator profile as you wish.


REV00449 Cannot purge - This is the only administrator profile
Explanation

An attempt has been made to delete the only administrator profile so that there is no longer an administrator profile. Adabas Review will not allow you to delete an administrator profile if another administrator profile is not available.

Action

If you intend to delete this administrator profile, first create another administrator profile. You can then delete the original administrator profile.


REV00450 Monitor DBID dbid prohibited by profile
Explanation

An attempt has been made to create, start or alter a report for a DBID that is not included in the DBID list of your user profile.

Action

Contact your system administrator to change your user profile or change the DBID you are trying to monitor in the report.


REV00451 User profiling is already installed
Explanation

An attempt was made to install the user profiling system when it is already installed.

Action

No action is necessary for this informational message.


REV00453 You must enter at least one DBID
Explanation

When editing an Adabas Review user profile, the option Monitor All Targets? was set to "N", however, a DBID was not specified. At least one DBID must be specified if this option is set to "N".

Action

Specify at least one DBID or set Monitor All Targets? to "Y".


REV0454 Profile reset to default values
Explanation

All values for the user profile you are viewing have been reset to the factory values.

Action

No action is required for this informational message.


REV00455 Group must be 'Y' or 'N'
Explanation

An invalid or blank value was entered in the Group Profile? option of the user profile. This option must be set to either "Y" or "N".

Action

Specify a valid value for the Group Profile? option.


REV00456 Info: Both "ALL TARGETS" and specific DBIDs are defined
Explanation

The user profile option Monitor All Targets? was set to Y but there are DBIDs listed. This is perfectly valid; in this case, the listed DBIDs have no effect on processing. However, if you later set the option to "N", the listed DBIDs will become the only valid DBIDs for the user.

Action

No action is necessary for this informational message.


REV00457 Invalid user ID
Explanation

The user ID entered on the user profile screen is invalid. User IDs must begin with a letter followed by any combination of alphanumeric or national (@#$) characters.

Action

Specify a valid user ID.


REV00458 Review Client engine status has been turned {ON |OFF}
Explanation

The Review Client status was toggled either on or off, as shown in the message.

Action

No action is required for this informational message.


REV00459 Review exit 2 is not installed
Explanation

While using the CM function, a call to communicate with client monitoring has determined that REVEXIT2 is not properly installed.

Action

Verify that the installation of REVEXIT2 has been performed correctly. For more information, refer to your Adabas Review (Phase 2) installation documentation.


REV00460 Review exit 2 is not active
Explanation

While using the CM function, a call to communicate with client monitoring has determined that REVEXIT2 is not active. It is possible to have REVEXIT2 linked into the link routine but not have it set to active in the LNKGBLS tables.

Action

Verify that the installation of REVEXIT2 has been performed correctly. For more information, refer to your Adabas Review (Phase 2) installation documentation.


REV00461 Response nnn received from REVEXIT2
Explanation

While using the CM function, a non-zero response code was returned from REVEXIT2. This is rare.

Action

Verify that the installation of REVEXIT2 has been performed correctly. For more information, refer to your Adabas Review (Phase 2) installation documentation. If you need additional assistance, contact your Software AG support representative.


REV00462 Ending apostrophe missing
Explanation

While editing the report processing rules for a report, an argument was specified with unpaired apostrophes.

Action

Correct the argument syntax and try again.


REV00463 Ending apostrophe incorrectly placed
Explanation

While editing the report processing rules for a report, an apostrophe was incorrectly used.

Action

Correct the syntax and try again.


REV00464 The maximum number of fields has been selected
Explanation

The maximum field limit has been reached. You cannot select any more fields.

Action

Evaluate the fields you have selected, removing ones you don't really need and adding ones you do, but be sure to stay within the maximum field limit.


REV00465 Unable to obtain SVC list
Explanation

While trying to use the AA function, the Adabas Review nucleus was unable to obtain the list of available SVCs on the current LPAR.

Action

Verify your Adabas Review installation is correct. If the problem persists, contact your Software AG support representative for assistance.


REV00466 Report option defaults converted successfully
Explanation

While editing a preexisting report after upgrading Adabas Review from version 4.4, the report defaults were converted to the current standard.

Action

No action is required for this informational message.


REV00467 Invalid character in field name
Explanation

While editing a report, an invalid character was used in one of the field names.

Action

Correct the field name syntax and try again.


REV00468 Cannot EC a non-client report
Explanation

An attempt was made to edit a non-client report using the EC command. The EC command only edits client reports.

Action

Use the ER command to edit a non-client report.


REV00469 Command line entries are not valid here
Explanation

When entering Adabas Review for the first time after upgrading from a previous version, a user profile conversion takes place. The only actions allowed are on the screen. Command line entries are not allowed for this special one-time event.

Action

Do not enter data on the command line while this conversion is taking place.


REV00470 NUCID only valid in local mode
Explanation

The NUCID command was used but SYSREVDB is currently communicating with an Adabas Review hub. The NUCID command is only valid when SYSREVDB is communicating with a local mode target.

Action

Do no use the NUCID command in hub mode.


REV00471 No NUCID was selected
Explanation

PF5 was pressed on a NUCID list screen but no NUCID was selected.

Action

Select a NUCID or use PF3 to exit the NUCID screen.


REV00472 NUCID has been changed
Explanation

Upon request, the NUCID was successfully changed.

Action

No action is required for this informational message.


REV00473 CM function only available in hub mode
Explanation

An attempt to turn on the client report engine using the CM command was made in local mode. The CM command is available only in hub mode.

Action

Operate Adabas Review in hub mode before attempting to start the client reporting engine.


REV00474 Parameter missing or invalid
Explanation

The required NAME parameter was omitted or invalid when using the batch Natural Review program COPYREP.

Action

Add or correct the parameter and rerun the job.


REV00475 Parameter is missing or invalid
Explanation

The required NEWNAME parameter was omitted or invalid when using the batch Natural Review program COPYREP.

Action

Add or correct the parameter and rerun the job.


REV00476 Invalid parameter specified
Explanation

When using a batch Natural Review program, an unknown or invalid parameter keyword was specified.

Action

Correct the error and rerun the job.


REV00477 STACKPARM= is incorrectly specified
Explanation

The optional STACKPARM parameter was incorrectly specified when using the batch Natural Review program COPYREP.

Action

Correct the error and rerun the job.


REV00478 NAME= and NEWNAME= parameters are required
Explanation

While using the batch Natural Review program COPYREP, both of the required parameters NAME= AND NEWNAME= were missing.

Action

Supply the correct parameters and rerun the job.


REV00479 Undefined keyword in input
Explanation

When using the batch Natural Review program COPYREP, an unknown parameter keyword was specified. Valid keywords are NAME, NEWNAME, STACKPARM and GO=YES.

Action

Supply only valid parameters and rerun the job.


REV00480 Words in report names must be separated by periods
Explanation

While using a batch Natural Review program that requires a report name as input, the report name did not have periods between each word. This is required to allow Natural to pass the parameters to the Adabas Review program correctly.

Action

Always place periods between words in report names. Correct the specification and rerun the job.


REV00481 Report already exists
Explanation

The new report name specified in the batch Natural Review program COPYREP already exists. COPYREP will not overwrite an existing report; instead it terminates with response code 12.

Action

Specify a unique name for the new report name or delete the report definition that already exists.


REV00482 Report definition has been purged
Explanation

This message confirms that the request to purge a report definition was successful.

Action

No action is necessary for this informational message.


REV00483 GO= parameter is incorrectly specified
Explanation

The GO= parameter specified in the batch Natural Review program COPYREP is specified incorrectly. The only valid syntax for this parameter is GO=YES.

Action

Correct the error and rerun the job.


REV00484 INVALID COST OPERATOR
Explanation

An invalid cost operator was entered on the Edit Report screen. Valid cost operators are:

  • "+": Plus -- add the cost factor to the field value.

  • "-": Minus -- subtract the cost factor from the field value.

  • "*": Multiply -- multiply the field value by the cost factor.

  • "@": Fixed -- apply a fixed cost to each command select by the report.

Action

Enter a valid cost operator if you want to use the cost feature.


REV00485 COST FACTOR REQUIRED IF OPERATOR IS PROVIDED
Explanation

A cost operator was entered on the Edit Report screen but no cost factor was provided. Both an operator and a cost factor must be specified to use the cost feature.

Action

Specify a cost factor for the field in addition to the operator or remove the cost operator from the field specification on the Edit Report screen.


REV00486 COST OPERATOR REQUIRED IF FACTOR IS PROVIDED
Explanation

A cost factor was entered on the Edit Report screen but no cost operator was provided. Both an operator and a cost factor must be specified to use the cost feature.

Action

Specify a cost operator for the field in addition to the cost factor or remove the cost factor from the field specification on the Edit Report screen.


REV00487 COST FACTOR MUST BE A POSITIVE VALUE
Explanation

A cost factor was provided on the Edit Report screen but the value is zero or negative. The values must be a positive or negative integer. Negative values can only be specified if the cost operator is "*" or "@".

Action

Specify a valid cost factor and try again.


REV00488 COST FACTOR IS NOT NUMERIC
Explanation

A cost factor was entered on the Edit Report screen that was not numeric. Only numeric values are valid.

Action

Specify a numeric value for the cost factor.


REV00489 ERROR WHILE TRYING TO RECATALOG USER EXIT
Explanation

During the first invocation of Adabas Review after a new installation or upgrade, an error occurred compiling and cataloging a user exit. The reason for the error cannot be determined.

Action

If the problem persists, examine and correct any user written exits. If no user exit has been written or modified, contact your Software AG technical support representative.


REV00490 COST FACTOR can only have 7 numeric digits
Explanation

A COST factor was entered on the Edit Report screen with eight numeric numbers and no decimal points. The maximum number of numeric digits is seven.

Action

Enter a value with no more than seven numeric digits. You may place a decimal point anywhere in the field if desired.


REV00491 COST OPERATOR '@' CAN ONLY BE USED FOR THE 'COMMANDS' FIELD
Explanation

A COST factor was entered on the Edit Report screen for the field COMMANDS but the operator was not the " @ " operator. The only operator allowed for the field COMMANDS is " @ ", indicating a FIXED cost. No other reporting field may use the " @ " operator.

Action

Either change the field name to something other than COMMANDS or change the Cost operator to " @ " and try again.


REV00492 COST IS ONLY VALID FOR SUM FIELDS
Explanation

A COST factor was entered into the ER screen for a field that is not a summary field. If the field does not have the SUM slot checked then COST is not possible.

Action

Correct the ER screen and try again.


REV00493 THIS FIELD IS NOT ALLOWED FOR DETAIL REPORTS
Explanation

A field was entered on the ER screen for a detail report that can only be used in a summary report.

Action

Remove the offending field.


REV00494 TARGET NAME MUST NOT BE BLANK
Explanation

The Target Name field must contain an alpha-numeric value. The field must not be all blanks.

Action

Enter a valid Target Name.


REV00495 REVIEW COMMANDS MUST BE 'Y' OR 'N'
Explanation

The Review Commands fields must contain a "Y" or an "N". All other values, including blank are invalid.

Action

Enter "Y" or "N".


REV00496 INVALID SYNTAX IN START PARAMETERS
Explanation

The Review command START or ST was entered into the command line to start an online report. The parameter data following the START command contained invalid syntax.

Action

Correct the error and re-submit.


REV00497 DBID VALUE IS NOT VALID
Explanation

The Review command START or ST was entered along with a DBID parameter.

The DBID parameter data contains invalid syntax.

Action

Correct the error and re-submit.


REV00498 DBID KEYWORD MUST BE FOLLOWED BY "="
Explanation

The Review command START or ST was entered along with a DBID keyword.

The DBID keyword must be followed by an equal sign (=). The equal sign was either missing or was an incorrect character.

Action

Correct the error and re-submit.


REV00499 DBID KEYWORD MUST BE PRECEEDED BY ","
Explanation

The Review command START or ST was entered along with a DBID keyword.

The DBID keyword must be preceded by a comma. The comma was either missing or was an incorrect character.

Action

Correct the error and re-submit.


REV00500 INVALID NUCID
Explanation

In LOCAL mode within a cluster environment, an attempt was made to alter the current nucleus ID, but the value entered was not valid. Valid values are 1 through 65535. Only numeric characters are allowed.

Action

Re-enter the nucleus ID using a valid value.


REV00501 CHANGE DBID PARAMETER ERROR(S)
Explanation

During a CHANGE DBID FROM operation, one or more parameter values were incorrect.

Action

Re-enter the CHANGE DBID command using valid values.


REV00502 INVALID INPUT PARAMETER(S)
Explanation

During a CHANGE DBID FROM operation, one or more parameter values were incorrect.

Action

Re-enter the CHANGE DBID command using valid values.


REV00503 FROM DBID IS INVALID
Explanation

During a CHANGE DBID FROM operation, the FROM DBID value was not valid. Valid values are 1-65535, ALL or NONE.

Action

Re-enter the CHANGE DBID command using valid values.


REV00504 INVALID DBID VALUE
Explanation

During a CHANGE DBID FROM operation, one or more of the DBID values were not valid. Valid values are 1-65535, ALL or NONE.

Action

Re-enter the CHANGE DBID command using valid values.


REV00505 FROM AND TO DBID CANNOT BE THE SAME
Explanation

During a CHANGE DBID FROM operation, both DBID values were identical. The values must be different.

Action

Re-enter the CHANGE DBID command using valid values.


REV00506 NO DBID(S) WERE CHANGED
Explanation

During a CHANGE DBID FROM operation, no DBIDs were found that match the FROM value.

Action

No action is required for this informational message.


REV00507 1 DBID HAS BEEN UPDATED
Explanation

During a CHANGE DBID FROM operation, one DBID was found that matched the FROM value and was updated with the TO value.

Action

No action is required for this informational message.


REV00508 nnn DBIDS HAVE BEEN UPDATED
Explanation

During a CHANGE DBID FROM operation, multiple DBIDs were found that matched the FROM value and were updated with the TO value.

nnn will show the number of reports updated.

Action

No action is required for this informational message.


REV00509 Invalid parameter for "ZIIP" command
Explanation

During a CHANGE DBID FROM operation, multiple DBIDs were found that matched the FROM value and were updated with the TO value.

Action

No action is required for this informational message.


REV00510 Review started with ZIIP=NO, zIIP disabled
Explanation

zIIP is installed, but Adabas Review was started with ZIIP=NO. The zIIP interface is disabled and cannot be turned on online, while Adabas Review is running.

Action

Start Adabas Review with ZIIP=YES.


REV00511 zIIP not installed
Explanation

An attempt to read the zIIP status returned a blank return character, indicating that zIIP is not installed.

Action

Install Adabas Review zIIP.


REV00512 Unkown data getting zIIP state: X
Explanation

An attempt to read the zIIP status returned an unkown return character for the zIIP state.

Action

Contact Software AG support.


REV00513 zIIP already switched on
Explanation

The command ZIIP=YES was issued, but zIIP is already active. zIIP state did not change.

Action

No action is required for this informational message.


REV00514 zIIP switched on
Explanation

The command ZIIP=YES was issued and zIIP was switched from inactive to active.

Action

No action is required for this informational message.


REV00515 Rsp=402, zIIP not supported
Explanation

An attempt was made to switch the zIIP state, but zIIP is not supported.

Action

Install Adabas Review zIIP.


REV00516 Unkown response code setting zIIP state: nnn
Explanation

An attempt was made to switch the zIIP state. But zIIP returned an uknown response code.

Action

Contact Software AG support.


REV00517 zIIP already switched off
Explanation

The command ZIIP=NO was issued, but zIIP is already inactive. zIIP state did not change.

Action

No action is required for this informational message.


REV00518 zIIP switched off
Explanation

The command ZIIP=NO was issued and zIIP was switched from active to inactive.

Action

No action is required for this informational message.


REV00519 Display of "ZIIP" statistics not allowed
Explanation

The display of zIIP statistics is disabled in the SYSREVDB user profile settings.

Action

Enable zIIP statistics in the user profile.


REV00520 Use of "ZIIP YES/NO" command not allowed
Explanation

The use of the ZIIP YES/NO command is disabled in the SYSREVDB user profile settings. ZIIP YES/NO changes the zIIP state (active/inactive).

Action

Enable ZIIP YES/NO command in the user profile.


REV00521 "ZIIP" command not allowed in User Profile System.
Explanation

An attempt was made to switch the zIIP state, but zIIP is not supported

Action

Issue the command outside the User Profile System.


REV00522 zIIP on Target must be Y(es) or N(o).
Explanation

The input value for the field "zIIP on Target" must be Y(es) or N(o). No means no zIIP clause will be generated in the parameters for autostarting. This equals to ZIIP=NO. Yes means ZIIP=YES will be generated.

Action

Enter correct value.


REV00523 Function "RG" not available for this report type.
Explanation

Display programs for Buffer Pool reports (BUFFPOOL) or for Pulse Reports (PU-00001) cannot be generated. They are delivered.

Action

If missing, move a backup copy to SYSREVDB.


REV00524 No targets are available for this SVC.
Explanation

On the Active Adabas SVCs screen, an SVC was selected but the SVC has no target associated with it.

Action

No action is required for this informational message.


REV00525 Report and saved definition do not match; REFRESH/REGEN necessary.
Explanation

Before a VW/VX command is executed, the running report and the saved definition will be checked. This is done by comparing the Account Record Length. For a running report this value is returned from the IN command. For the saved definition this value is calculated.

If the calculation is not possible, e.g. because a user-defined variable is missing, the check will be ignored and the VW/VX will be executed without check.

Action

Refresh the running report and/or regenerate the report and the display program with its original definition.


REV00526 In local mode the DBID to monitor may be the local DBID only.
Explanation

Adabas Review running in local mode can collect data on its local DBID only. Thus the DBID-to-be-monitored and the local DBID must be the same. Use the HUB mode to monitor several different DBIDs.

Action

Enter the local DBID or ALL as DBID-to-be-monitored and/or update the report definition.


REV00527 No NUCID found for TARGET dbid.
Explanation

An attempt to read NUCID(s) from a local DBID did not return any NUCID. Most probably the DBID is not a cluster. Or the Adabas call to read the NUCIDs failed.

Action

Enter the correct local TARGET DBID or check the Adabas cluster environment.


REV00528 TARGET not initialized, set to default value dbid.
Explanation

The Adabas Review local or HUB TARGET dbid was not yet initialized, i.e. the value was 0. The TARGET has been set to the default value, derived from the REVIEW-DB dbid or the user profile.

Action

No action required if the TARGET is the desired one. Otherwise set the TARGET in advance with the batch Natural SET command.