ERROR-121 | ERROR-122 | ERROR-123 | ERROR-124 | ERROR-125 | ERROR-126 | ERROR-127 | ERROR-128 | ERROR-129 | ERROR-130 | ERROR-131 | ERROR-132 | ERROR-133 | ERROR-134 | ERROR-135 | ERROR-136 | ERROR-137 | ERROR-138 | ERROR-139 | ERROR-140 | ERROR-141 | ERROR-142 | ERROR-143 | ERROR-144 | ERROR-145 | ERROR-146 | ERROR-147| ERROR-121 | Invalid ISNLIST parameter The value of the ISNLIST parameter is wrong. Check for the following: overlapping ISN ranges the same ISN supplied more than once an ISN with a value of 0 Investigate the cause of the error. Correct it and rerun the job. |
| Explanation |
This error is produced when the value of the ISNLIST parameter is wrong. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-122 | DARC must be a value between 0 and 3 |
| Explanation |
An invalid value was specified for the DARC parameter. A value between 0 and 3 is expected. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-123 | LRPL must be in the range 300,000 - 2,147,483,647 |
| Explanation |
An invalid value was specified for the LRPL parameter. The value must be greater than or equal to 300,000 and less than 2,147,483,648. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-124 | Parameter HOLD must be set to YES or NO. |
| Explanation |
An invalid value was specified for the HOLD parameter. Valid values are YES or NO. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-125 | Replication is not enabled. Database is not enabled for replication. |
| Explanation |
The source database is not running with ADARUN REPLICATION=YES. |
| Action |
Correct the ADAUN REPLICATION parameter setting, stop and restart the source database and rerun the job. |
| ERROR-126 | ADARIS and Reptor_module are not on the same version/release level. |
| Explanation |
The ADARIS utility and the Event Replicator Server module are not for the same version of the Event Replicator for Adabas. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-127 | File nnnnn is an expanded file. |
| Explanation |
The ADARIS utility does not support expanded files. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-128 | Module_name returned response code nnn. |
| Explanation |
The module named in the message (Module_name) returned the response code shown in the message (nnn). |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-129 | DMAXOUTPUTSIZE must be greater than 4,095, less than 2,147,483,648 or 0. |
| Explanation |
An invalid value was specified for the DMAXOUTPUTSIZE parameter. Valid values must be greater than 4,095 and less than 2,147,483,648. They can also be zero. |
| Action |
Verify and correct input parameters for the ADARIS run. Then try again. |
| ERROR-130 | ADARIS replication pool overflow. |
| Explanation |
A replication pool overflow occurred. |
| Action |
Increase the setting for the LRPL ADARUN parameter and rerun the job. |
| ERROR-131 | Load failure for Exit name |
| Explanation |
An attempt failed to load the user exit listed in the message (name). |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-132 | ADARIS initialization terminated at the request of destination output user exit exitname |
| Explanation |
ADARIS initialization was terminated due to processing requested by the user exit listed in the message (exitname). |
| Action |
No action is required for this informational message. |
| ERROR-133 | File fnr does not exist in the database. |
| Explanation |
The file number (fnr) specified for the FILE parameter does not exist in the database. |
| Action |
Correct the file number and rerun the job. |
| ERROR-134 | Replication is not enabled |
| Explanation |
Replication is not enabled for the specified file, so it is not replicated. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-135 | Subscription sname does not exist on Replicator system file on the Reptor database dbid or DBID=dbid / File=fnr is not defined in the subscription. |
| Explanation |
Either the named subscription (sname) has no definition in the Replicator system file on the database listed in the message (dbid) or the database and file number listed in the message (dbid and fnr) are not defined in the subscription. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-136 | Reptor response code rsp. Reptor yyyyy is not active. |
| Explanation |
The Event Replicator Server listed in the message (yyyyy) is not active. The response code received from an Adabas call to the Event Replicator Server is given in the message (rsp). |
| Action |
Start the Event Replicator Server and rerun the job. |
| ERROR-137 | Replicator system file is not loaded on the Replicator database. |
| Explanation |
The Replicator system file is not loaded on the Event Replicator Server database specified. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-138 | DBID=dbid / File=fnr is not defined in the subscription sname. |
| Explanation |
The database ID and file number combination listed in the message (dbid and fnr) are not defined in the subscription named in the message (sname). |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-139 | GETMAIN for the replication pool failed. |
| Explanation |
The ADARIS utility was unable to get storage for the replication pool.
The size of the replication pool is set via ADARIS parameter
|
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-140 | Unable to open the sequential output file DDOUT. |
| Explanation |
A non-zero response code was produced when ADARIS attempted to open
the sequential file listed in the |
| Action |
Use the error messages to analyze and correct the problem. |
| ERROR-141 | Internal error at ADARPD+yyy R0-R3 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX R4-R7 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX R8-R11 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX R12-R15 XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX |
| Explanation |
An internal error occurred. The offset in ADARPD is given in the message (yyy). The register contents at the time of the error are also listed. |
| Action |
Inform your database administrator. |
| ERROR-142 | An error occurred reading the replication definitions from the Replicator system file. |
| Explanation |
An error occurred while attempting to read the replication definitions from the Replicator system file. |
| Action |
Look in the |
| ERROR-143 | An error occurred writing to the sequential output file DDOUT. |
| Explanation |
An error occurred during an attempt to write to the sequential file
identified in the job by the |
| Action |
Look in the job log output for further information about the error. Correct it and rerun the job. |
| ERROR-144 | Subscription xxxxxxxx database nnnnn file nnnnn xxxxx image uses global format buffer xxxxxxx This is an optimized GFB, parameter DCLASS=SAGTARG. or SAGTRGB is required. |
| Explanation |
The global format buffer image is optimized and can only be used when
the parameter |
| Action |
Include the parameter |
| ERROR-145 | Parameter READOPTION must be set to BLANK or I. |
| Explanation |
An invalid value was specified for the READOPTION parameter. Valid values are BLANK or I. |
| Action |
Investigate the cause of the error. Correct it and rerun the job. |
| ERROR-146 | Date and Time must be reasonable.
Date must be entered in the form YYYYMMDD with YYYY >= 2016 Time must be entered in the form HHMMSS and < 240000 |
| Explanation |
One or more of the specified date and time fields appear invalid. |
| Action |
Correct the date and time entries and try again. |
| ERROR-147 | STARTDATE value required when STARTTIME is specified |
| Explanation |
The STARTDATE parameter is required when the STARTTIME parameter is specified. |
| Action |
Add the STARTDATE parameter or remove the STARTTIME parameter and try again. |