ADACNV Utility Messages

Version number specified with parameter "TOVERS" is not supported by ADACNV.

Change the parameter to a supported version and rerun the utility.

The current version of the database is 5.1 or below. Conversion could only be performed from version 5.2 and above.

Convert the database to version 5.2 by starting and stopping the version 5.2 Adabas nucleus, then rerun ADACNV.

The DIB block is not empty, conversion is not possible.

Shut down the Adabas nucleus, wait for all utilities to complete, and rerun ADACNV.

The Work data set is not empty. Conversion is not possible.

To remove the pending autorestart, restart the nucleus and end it normally.

The DDFILEA block size ("block size" bytes) is too small to write a record with a length of "length" bytes.

Assign DDFILEA to a device type with a larger sequential block size.

You cannot convert to the version listed in the message (vr) because the file listed in the message (fn) does not fit into four Associator blocks.

Delete the file listed in the message (fn) and rerun the ADACNV job.

DDFILEA (FILEA) has an invalid structure. This is probably a job control (JCL) statement error.

Correct any error and rerun the ADACNV job.

You cannot convert to the version you requested because at least one version vr feature was used for the file listed in the message (fn).

Remove the version vr features and rerun the ADACNV job.

The PLOGRn data set is not free. Conversion fails.

Run ADARES PLCOPY to free the PLOG data set(s); then rerun the ADACNV job.

Alternate RABNs are not supported by Adabas version 7.2 and above.

Use ADAORD to reorder the database before converting it from a version of Adabas version 7.1 or below to Adabas version 7.2 or above.

The parallel participant table (PPT) entry contains a protection log (PLOG) data set with the specified number and name. ADACNV was unable to open the data set. The data set may have been deleted, or it may not be cataloged, or it may contain PLOG data that has not yet been copied.

Provide access to the specified data set or use the IGNPPT parameter and rerun the job.

The parallel participant table (PPT) entry contains a protection log (PLOG) data set with the name and number specified. ADACNV was unable to read the first block of this data set. The data set has probably been destroyed.

Determine the cause of the error; correct it and rerun the job.

Backward conversion of an Event Replicator Server is not supported prior to Adabas version 7.4.

Investigate the cause of the error.

Backward conversion of a database is not possible when a Replicator or SLOG system file is loaded.

Investigate the cause of the error.

The allocation of the PPT area failed. An attempt was made to allocate n ASSO blocks.

Correct the error and rerun the job.

The database has more than five physical ASSO or DATA extents. It cannot be reverted back to an Adabas 7 database.

Contact your Software AG technical support representative for assistance.

One or more system file numbers is greater than 255.

Adjust the system file numbers so they are less than 255 and try again.

The Adabas version of the database is the same as the version requested in the ADACNV run.

No action is required for this informational message.

Adabas 7 allowed a maximum of six user system files (files loaded with the SYSFILE option). More than six user system files currently exist.

Unload, delete, and reload the additional user system files without the SYSFILE option. Then rerun this utility.

The user system file identified in the message (nnnnn) exists in the reserved area of the GCB.

Unload, delete, and reload the system file with the SYSFILE option to place the file number in the correct area of the GCB. Then rerun this utility.

The file identified in the message (nnnn) is using a new index structure. It cannot be converted backward to a version prior to Adabas 8.3

Run ADAREP to identify all files that have the advanced index structure. For those files, ADAREP prints the line ‘Index structure ... Advanced’ in the file detail section. Eliminate the new index structure, then rerun this utility. There are a number of ways the new index structure can be eliminated:

• Unload, delete, and reload the file.

• Run the ADAORD REORASSO utility function.

• Run the ADAORD REORDB utility function.

• Run the ADAORD REORFASSO utility function for that file.

• Run the ADAORD REORFILE utility function for that file.

• Run the ADAORD RESTRUCTUREDB utility function followed by the ADAORD STORE utility function.

• Run the ADAORD RESTRUCTUREF utility function followed by the ADAORD STORE utility function for that file.

In the first phase of conversion, this message is printed to indicate that the conversion of the database is possible.

The ADACNV utility has begun its final pass. Any abend after this point requires a new run of the utility with the RESTART parameter.

In the first phase of conversion, a conversion step has started.

The conversion step has been successfully completed.

Adabas Reflective Database is not supported by Adabas version 7 and above.

Alternate RABNs are not supported by Adabas version 7.2 and above.

Security-by-value conversion has been successfully completed.

At least one FST entry does not fit into one FST block due to the FST structure change. The entry or entries with the smallest RABN range(s) are deleted.

ADACNV finishes with a warning and response code 4 (ADARSP004).

Run ADAORD REORDB after conversion.