ADAULD Utility Error Messages

The file is ciphered but no cipher code is supplied.

Supply the correct cipher code and rerun the ADAULD job.

Remove the cipher code and rerun the ADAULD job.

No records found according to the given search criterion. The resulting unloaded file contains only the field definition table (FDT).

"error-count" errors have occurred (the displayed message contains an actual count). ADAULD execution is terminated.

NUMOUT must be 1 or 2. If NUMOUT=2, user exit 9 must is loaded.

Supply a correct parameter or a user exit, and rerun the job.

Supply a valid selection criterion and rerun the job.

The LRECL and LPB parameters must be less than 32,768.

Supply the correct parameter value and rerun the ADAULD job.

The maximum record lengths of the output data sets must be equal.

Supply the correct output data sets and rerun the ADAULD job.

The field cannot be used to determine the unload sequence because it

• is undefined;

• is not a descriptor;

• is a phonetic descriptor; or

• (or part of the field) is within a periodic (PE) group.

Choose another sequence, and rerun the ADAULD job.

Unloading the file in descriptor "desc-name" sequence may lead to variations in the normal sequence (anomalies).

If you nevertheless want to perform that unload sequence, supply the "option" parameter. Otherwise, choose another unload sequence. Then rerun the ADAULD job.

The file to be unloaded is not defined with the multiclient option.

Remove the ETID parameter and rerun the ADAULD job.

The file to be unloaded is defined with the multiclient option. Selecting records according to a search criterion requires that a single ETID be specified.

Specify the ETID parameter, and rerun the ADAULD job.

Checkpoint and security files may not be unloaded.

Supply a correct input file and rerun the job.

The data set supplied as the DD/SAVE input data set is not a save tape.

Supply a valid save tape and rerun the job.

Once of the following occurred:

• The requested protection log has DBID dbid1, session number plognum1, but the supplied protection log has DBID dbid2, session number plognum2.

• The SYN1/SYN4 checkpoint is not contained in the protection log block blocknumber.

• The SYN2/SYN5 checkpoint is not contained anywhere on the protection log.

• Another SYN1/SYN4 checkpoint was encountered before the expected SYN2/SYN5 checkpoint.

• The supplied input tape is not a protection log.

Supply the correct protection log and parameters, and rerun the job.

The temp data set is not large enough to buffer all Data Storage blocks found for file file-number on the protection log.

Supply a larger temp data set and rerun the job.

The tapes of a multivolume data set are mounted in the wrong order. ADAULD terminates.

Supply the tapes in the correct order and rerun the job.

An error occurred while the Adabas Delta Save Facility Facility was processing the requested function for the delta save data set. The Delta Save Facility returned the response code provided in the message.

Refer to the information for the specified response code. Correct the error and rerun the job.

The full save tape required to unload from a delta save data set is not supplied.

Supply the full save data set and rerun the job.

A valid value has at most eight (8) digits or blanks.

Supply a valid parameter value and rerun the job.

The unloaded file was changed during an online save operation but no protection log is supplied. The unloaded data is probably inconsistent.

The DDISN parameter must not be specified if SORTSEQ=descriptor,MU is also specified, or if the descriptor specified with SORTSEQ is a hyperdescriptor.

Supply the correct parameter value and rerun the job.

The record format of DD/EBAND and DD/ISN must be V or VB.

Supply the correct input and rerun the job.

When running DECOMPRESS on a multiclient file, Adabas processes either

• the entire file if ET-ID is not specified; or

• the selection of records allowed for the client identified by ET-ID.

The user ID referred to by the `ETID' parameter is either not defined or has not been assigned an owner ID.

Investigate the cause of the error; correct it; and rerun the job.

While unloading a file from SAVETAPE, the descriptor value table (DVT) could not be created because the file contains a hyperdescriptor but the hyperdescriptor exit was not specified in the ADARUN parameters for the database.

Specify ADARUN HEXnn parameter in the ADARUN parameters for the database and rerun the job. For more information about the HEXnn parameter, read HEXnn: Hyperdescriptor User Exit.

An error was encountered while generating the descriptor value table (DVT) when a file was being unloaded from SAVETAPE. A response code is returned. For more information, read Nucleus Response Codes.

Investigate the cause of the error, correct it, and rerun the job.

The maximum record length of the output data set is to small.

Specify the correct output data set or a data set with the correct maximum record length and rerun the job.

A hyperdescriptor exit call failed with response code 79 (ADARSP079) and the subcode given in the message during SAVETAPE processing.

Investigate the subcode to determine the reason for the error.

The SAVETAPE identified in the message (tape) does not contain expected data. All records on the tape must contain references to DBID dbid1, session number n1, and time stamp tttt1. However, a record was found that incorrectly referred to DBID dbid2, session number n2, and time stamp tttt2

Correct the cause of the incorrect reference and rerun the ADAULD job.

At least one field was found with the collation descriptor option defined. In this case, MODE=SHORT is required. Adabas has forced this parameter setting.

None required. This message is for information only.