Version 8.2.5
 —  Messages and Codes  —

ADAQ* - Adabas Review Hub Messages

ADAQnn messages are received from the Adabas Review hub.

Note:
Each of the messages in this section starts with the relevant database ID.

Overview of Messages

ADAQ89 | ADAQ90 | ADAQ91 | ADAQ92 | ADAQ93 | ADAQ94 | ADAQ95 | ADAQ96 | ADAQ99

ADAQ89 dbid POSSIBLE CONFLICT BETWEEN REVIEW HUB AND UEX4.
RAOSEXIT DISABLED
Explanation

The Adabas Review hub was enabled by specifying a hub ID on the ADARUN REVIEW parameter. The ADARUN UEX4 parameter was also specified and the user exit 4 module was identified as RAOSEXIT, an Adabas Review user exit that is not compatible with the Adabas Review hub. The Adabas nucleus completes its initialization but no calls to user exit 4 are performed by ADALOG.

Action

If the UEX4 parameter is left over from a previous conversion, remove the parameter. Otherwise, supply the correct user exit 4 module name.


ADAQ90 dbid REVIEW HUB INACCESSIBLE BECAUSE REVIEW HUB ID WAS NOT SPECIFIED
Explanation

The value specified for the Adabas Review hub was invalid. The Adabas nucleus completes its initialization but no calls are made to the Adabas Review hub.

Action

Specify the correct Adabas Review hub ID value and restart the nucleus.


ADAQ91 dbid module-name MONITORING SYSTEM INITIALIZATION FAILED.
SEE ERROR MESSAGES
Explanation

The specified monitoring system component returned a nonzero status. Any failure of this sort should be accompanied by error messages displayed by the monitoring system. The Adabas nucleus completes its initialization but no calls are made to the monitoring system.

Action

Check the monitoring system error messages, correct the cause of the error, and restart the nucleus.


ADAQ92 dbid module-name MONITORING SYSTEM WAS NOT LOADED.
CONTACT YOUR VENDOR
Explanation

The specified monitoring system component could not be loaded. It is possible that the load library containing the expected module was not specified in the nucleus' job stream. The Adabas nucleus completes its initialization but no calls are made to the monitoring system.

Action

Correct the cause of the error and restart the nucleus.


ADAQ93 dbid module-name MONITORING MAY BE INCOMPLETE BECAUSE ADALOG IS NOT LOADED.
Explanation

The command logging module ADALOG was not loaded. The monitoring system will not be able to process any command log records. The Adabas nucleus completes its initialization but no calls are made to the monitoring system.

Action

Correct the cause of the error and restart the nucleus


ADAQ94 dbid module-name IS AN INCORRECT VERSION LEVEL.
CONTACT YOUR VENDOR
Explanation

The specified module is at an incorrect version level and cannot be used with this version and/or SM-level of Adabas. The Adabas nucleus completes its initialization but no calls are made to the monitoring system.

Action

Contact your monitoring system vendor to determine if the correct module is being used or supplied.


ADAQ95 dbid module-name DOES NOT HAVE THE CORRECT PIM.
CONTACT YOUR VENDOR
Explanation

The specified module is incompatible with this version and/or SM-level of Adabas. The Adabas nucleus completes its initialization but no calls are made to the monitoring system.

Action

Contact your monitoring system vendor to determine if the correct module is being used or supplied.


ADAQ96 dbid module-name CANNOT MONITOR IOR CALLS AT THIS TIME.
UNUSUAL ERROR
Explanation

Adabas cannot give control to the specified monitoring system module for purposes of monitoring I/O activity. The Adabas system-dependent interface module was not properly loaded. The Adabas nucleus completes its initialization but no calls are made to the monitoring system.

Action

Note the error message number and module name and call your Software AG technical support for assistance.


ADAQ99 dbid REVIEW HUB ID EQUAL TO ADABAS DBID IS NOT PERMITTED.
REVIEW HUB INACCESSIBLE
Explanation

The specified Adabas Review hub ID value is identical to the value specified for the DBID parameter. The Adabas Review hub cannot have the same target ID as that of the Adabas nucleus. The Adabas nucleus completes its initialization but no calls are made to Adabas Review.

Action

Correct the hub ID value on the REVIEW parameter and restart the nucleus.


Top of page