NETP* - Simple Connection Line Driver Messages

Link llllllll, which was previously suspended, has resumed processing as a result of the RESUME command.

None.

NWTCPOPC

Message processing has been suspended on link llllllll as a result of the SUSPEND command.

Issue the RESUME command to restart message processing when appropriate.

NWTCPOPC

An operator command was issued, however, the value specified for the link name was not "*", "#" or a valid link name. The command is ignored.

Reissue the command with a correct link name or a wild card value.

NWTCPOPC

An operator command was issued. The command passed initial parsing, that is, each subcommand was processed. The success or failure of a subcommand is independent of this message being issued.

None.

NWTCPOPC

Statistics for link lllllll or the TCPI driver have been either printed or reset, as indicated by xxxxxxxx.

None.

NWTCPOPC

An attempt to alter the active configuration for link llllllll or the TCPI driver has failed due to invalid parameter specifications in the command TCPI lllllll ALTER xxxx, where llllllll is a link name or a wildcard value and xxxx is one or more configuration keywords and parameters. The cause of the problem may be one of the following:

• A parameter specification contains a typographical or format error that makes the specification invalid.

• A value specified as the operand for a specific keyword is out of range, of incorrect format, or otherwise invalid.

• A keyword that is valid only when the link or driver is closed was specified when the link or driver was open.

If a keyword that is valid only when the link or driver is closed was specified, close the link or driver and reissue the command. Be aware that if the value specified for the RESTART parameter is too low, the link or driver may be automatically reopened after the CLOSE command is issued and before the ALTER command can be reentered. To prevent this, specify CLOSE (CL) in the command string immediately before the subcommand ALTER. For example:

TCPI linkname CL ALTER INETADDR=(127,0,0,1)

If the specified keywords are valid for the current state of the link or driver, verify that the keywords are spelled correctly, that all punctuation is correct, and that the operands are valid.

NWTCPOPC

A TCPI command was issued to one or more links or to the TCPI driver, and the action identified by xxxxxx was taken as a result.

None.

This message is issued in response to an operator command that was sent to link or driver llllllll. The link or driver name is followed by informational message text, which is one of the following:

Invalid State For Cmnd - The driver or link was in an invalid state (open) for the command to be executed.

Configuration Altered - The driver or link configuration was successfully updated.

Manual Open Failed - Open processing failed.

Connect In Progress - Connect processing for the link has been initiated.

Disconnect In Progress - Disconnect processing for the link has been initiated.

No action is required unless the message is 'Invalid State For Cmnd'. If so, wait for the link or driver to go into the proper state; then reissue the command, if appropriate.

NWTCPOPC

This multi-line display shows the current configuration for link llllllll. The parameters displayed may be different from those specified at Entire Net-Work initialization if they have been modified manually, or if they have been modified internally as a result of being out of range. For example, the last line appears only if IP Version 6 is in use.

None.

NWTCPOPC

The current state of link or driver llllllll is displayed with a count of messages sent and received. The message counts are for the period of time since the driver was opened, the link connected, or the statistics reset for either the driver or the link.

This message is automatically produced as a result of a command being issued to a link or driver while the link or driver was in an incorrect state for the command or as a result of a TCPI llllllll STATUS command being issued.

None.

NWTCPOPC

This multi-line display shows the current configuration for driver dddd. The parameters displayed may be different from those specified at Entire Net-Work initialization if they have been manually modified or if they have been modified internally as a result of being out of range.

Note:
The client table size is initially determined by the NUMUSERS parameter setting.

None.

NWTCPOPC

    +----------------------------------------------------------------------+
(a) + Statistics For Link XXXXXXXX  Period xxxxx:xx:xx (xxxxxxx.xxx Secs)  +
    + -------------  ---Bytes----  --Messages--  -Api Calls--  ----------- +
(b) + Writes         xxxxxxx.xxxz xxxxx,xxx,xxx Xxxxx,xxx,xxx  Total       +
(c) + xxxxxxx.xxxz xxxxx,xxx,xxx Xxxxx,xxx,xxx  Per Second  +
(d) + Reads          xxxxxxx.xxxz xxxxx,xxx,xxx Xxxxx,xxx,xxx  Total       +
(e) + xxxxxxx.xxxz xxxxx,xxx,xxx Xxxxx,xxx,xxx  Per Second  +
    + -------------  ---Total----  ----Task----  ---Other----  ----------- +
(f) + WRITE Cmds  xxxxx,xxx,xxx  xxxxx,xxx,xxx xxxxx,xxx,xxx   Total       +
(g) +              xxxxx.xxx.xxx  xxxxx,xxx,xxx Xxxxx,xxx,xxx  Per Second  +
(h) + REAC Cmds   xxxxx,xxx,xxx  xxxxx,xxx,xxx xxxxx,xxx,xxx   Total       +
(i) +              xxxxx,xxx,xxx  xxxxx,xxx,xxx Xxxxx,xxx,xxx  Per Second  +
    +----------------------------------------------------------------------+

This multi-line display is produced when the command TCPI xxxx STATS is issued, or when the automatic statistics interval has expired and PSTATS=Y is specified in the LINK statement. Values are displayed and updated asynchronously; therefore, the totals displayed may not always be accurate.

The display contains the following information:

None.

NWTCPOPC

This multi-line display is produced when you issue the USERS operator command for the Simple Connection Line Driver. The type in the message indicates whether the statistics listed in the output are for a driver or a link. The name in the message indicates the name of the driver or link to which the statistics apply.

This is a sample of the output that will appear when issued to the driver:

NETP065I: Active Users For Driver TCPX                                 
NETP065I: --------- Client ID     1 -----------------                  
NETP065I: Active on Link TCX00001 TCP/IP address 10.132.33.48          
NETP065I: Adabas Userid:                                               
NETP065I: Char(        NET-WORKS   NORGAY    )                           
NETP065I:  Hex(01210000 00000000 D5C5E360 E6D6D9D2 E22B0001 D2C5D5E3 40404040)
NETP065I: Context ID(E22B0001) Context Verifier(01000000)              
NETP065I: Number of requests processed           1                     
NETP065I:     1 Active Users printed              

This is a sample of the output that will appear when issued to a link:

NETP065I: Active Users For Link TCX00001 TCP/IP address 10.132.33.48  
NETP065I: --------- Client ID     1 -----------------                 
NETP065I: Adabas Userid:                                              
NETP065I: Char(        NET-WORKS   NORGAY    )                          
NETP065I:  Hex(01210000 00000000 D5C5E360 E6D6D9D2 E22B0001 D2C5D5E3 40404040)
NETP065I: Context ID(E22B0001) Context Verifier(01000000)             
NETP065I: Number of requests processed           1                    
NETP065I:     1 Active Users printed                                                       
                                 

None.

NWXTSOPC

This multi-line display shows the current configuration for the Simple Connection Line Driver link llllllll. The parameters displayed may be different from those specified at Entire Net-Work initialization if they have been modified manually, or if they have been modified internally as a result of being out of range.

None.

NWXTSOPC

This multi-line display shows the current configuration for the Simple Connection Line Driver. The parameters displayed may be different from those specified at Entire Net-Work initialization if they have been manually modified or if they have been modified internally as a result of being out of range.

Note:
The client table size is initially determined by the NUMUSERS parameter setting.

None.

NWXTSOPC

All connect queue entries are in use.

The number of connect queue entries is specified by the CONNQUE parameter on the DRIVER statement. Increase the value of this parameter to accommodate the maximum number of simultaneous connection requests from remote nodes.

An error occurred when attempting to obtain or release virtual storage. This error usually occurs because there is insufficient storage in the region to satisfy the obtain or one of the buffer pools is not large enough to satisfy the storage request.

Check the buffer pool statistics by issuing the DISPLAY STATS operator command. If necessary, increase the size of the buffer pools. Otherwise, increase the private area size of the region to allow storage requests that are not allocated from buffer pools to properly complete.

NWTCPCNS

There was an error in acquiring storage to perform a passive OPEN call to the TCP/IP partition. RC = 4 indicates a problem acquiring partition GETVIS storage. RC = 16 indicates a problem acquiring SVA GETVIS storage.

For RC=4, increase the size of the Entire Net-Work partition or decrease the SIZE parameter on the EXEC card if possible. With RC=16, additional allocation is required in the system GETVIS area in the SVA. For other values, contact your Software AG technical support representative.

NWVSESTK

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on a passive OPEN(Listen) call.

Report the error to your Software AG technical support representative.

NWVSESTK

There was an error in acquiring storage to perform an OPEN call to the TCP/IP partition. RC is the return code from a z/VSE GETVIS call. For more information, refer to the appropriate z/VSE documentation.

For RC=4, increase the size of the Entire Net-Work partition or decrease the SIZE= parameter on the EXEC card if possible. With RC=16, additional allocation is required in the system GETVIS area in the SVA. For other values, contact your Software AG technical support representative.

NWTCPCNS

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on an OPEN call.

Report the error to your Software AG technical support representative.

NWTCPCNS

There was an error in acquiring storage to perform a SEND call to the TCP/IP partition. RC is the return code from a z/VSE GETVIS call. For more information, refer to the appropriate z/VSE documentation.

For RC=4, increase the size of the Entire Net-Work partition or decrease the SIZE= parameter on the EXEC card if possible. With RC=16, additional allocation is required in the system GETVIS area in the SVA. For other values, contact your Software AG technical support representative.

NWTCPCNS

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on a SEND call.

Report the error to your Software AG technical support representative.

NWTCPCNS

There was an error in acquiring storage to perform a RECEIVE call to the TCP/IP partition. RC is the return code from a z/VSE GETVIS call. For more information, refer to the appropriate z/VSE documentation.

For RC=4, increase the size of the Entire Net-Work partition or decrease the SIZE= parameter on the EXEC card if possible. With RC=16, additional allocation is required in the system GETVIS area in the SVA. For other values, contact your Software AG technical support representative.

NWTCPCNS

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on a RECEIVE call.

Report the error to your Software AG technical support representative.

NWTCPCNS

There was an error in acquiring storage to perform an CLOSE call to the TCP/IP partition. RC is the return code from a z/VSE GETVIS call. For more information, refer to the appropriate z/VSE documentation.

For RC=4, increase the size of the Entire Net-Work partition or decrease the SIZE= parameter on the EXEC card if possible. With RC=16, additional allocation is required in the system GETVIS area in the SVA. For other values, contact your Software AG technical support representative.

NWTCPCNS

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on a CLOSE call.

Report the error to your Software AG technical support representative.

NWTCPCNS

There was an error in acquiring storage to perform an OPEN CONTROL call to the TCP/IP partition. RC is the return code from a z/VSE GETVIS call. For more information, refer to the appropriate z/VSE documentation.

For RC=4, increase the size of the Entire Net-Work partition or decrease the SIZE= parameter on the EXEC card if possible. For RC=8, correct the value of the USERID parameter on the DRIVER statement to match the ID= subparameter of the PARM field for an active TCP/IP stack. With RC=16, additional allocation is required in the system GETVIS area in the SVA. For other values, contact your Software AG technical support representative.

NWTCPCNS

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on an OPEN CONTROL call.

Report the error to your Software AG technical support representative.

NWTCPCNS

There was an error in acquiring storage to perform a CLOSE,CONTROL call to the TCP/IP partition. RC is the return code from a z/VSE GETVIS call. For more information, refer to the appropriate z/VSE documentation.

For RC=4, increase the size of the Entire Net-Work partition or decrease the SIZE= parameter on the EXEC card if possible. With RC=16, additional allocation is required in the system GETVIS area in the SVA. For other values, contact your Software AG technical support representative.

NWTCPCNS

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on a CLOSE CONTROL call.

Report the error to your Software AG technical support representative.

NWTCPCNS

An error was received while executing a call to resolve the host name or address. RC is the contents of Register 15 on return from the call. For more information, see the appropriate z/VSE documentation.

The action to take depends on the return code (RC=), as shown in the following table:

NWTCPCNS

RC is the return code passed back to Entire Net-Work by the TCP/IP partition on a call to resolve the host name or address.

Report the error to your Software AG technical support representative.

NWTCPCNS

A call to the IBM TCP/IP HPS API failed for function xxxxxxxx. The error number nnnnn provides the reason the failure and sssss is the socket where the failure occurred. This message provides diagnostic information about a previous error message. It may also be followed by a NETP601I message that explains the error number.

Locate message NETP601I for a description of the error number.

NWTCPHPS

This message describes the error number provided in message NETP600I.

Try to eliminate the condition that caused the message.

NWTCPHPS

An invalid request was made to the API.

Contact your Software AG technical support representative.

NWTCPHPS

An attempt to load a required module for TCP/IP failed. The driver and all links using this API will be unusable. This is most likely caused by TCP/IP not being correctly installed. It could also be caused by a short-on-storage condition or an I/O error.

Check the joblog and syslog for any additional messages, such as operating system messages, that may provide a reason for the problem.

NWTCPHPS

An attempt to allocate storage for a required control block failed. The control block is needed for the driver and all active links using the API. Only the new link being connected to or the new driver being opened is affected. All active links and drivers continue to run as long as the storage shortage does not cause other problems with Entire Net-Work.

Look for other messages indicating storage problems and perform any recommended action.

NWTCPHPS

An error occurred while trying to close a socket used for a connection. The Entire Net-Work connection is closed, but the socket is not usable for future connections.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

A TCP/IP driver using API=HPS has been closed.

None required. This message is informational only.

NWTCPHPS

API=HPS was specified for a driver on a system that does not support it. MVS is currently the only operating system that supports this API.

Specify a valid API for the system and the TCP/IP stack that you are running.

NWTCPHPS

An INITAPI function call was made to TCP/IP and failed. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

A call made to TCP/IP to get a new socket failed. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information. You may need to adjust some TCP/IP parameters to allow for more sockets.

NWTCPHPS

A BIND function call to TCP/IP failed. The BIND function tells TCP/IP which port to listen on, as well as any restrictions on who can connect to this port. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

A GETSOCKOPT function call to TCP/IP failed. The GETSOCKOPT function is used to determine the maximum message size that can be sent. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

A LISTEN function call to TCP/IP failed. The LISTEN function is used to set the number of connection requests that can be queued. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

An ACCEPT function call to TCP/IP failed. The ACCEPT function waits for a connection request and returns a socket to be used for the new conversation. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

The connection request was rejected because there was no connect queue entry available to process the request.

Increase the value of the CONNQUE parameter on the DRIVER statement.

NWTCPHPS

A SETSOCKOPT function call to TCP/IP failed. The SETSOCKOPT function is used to set the KEEPALIV parameter on the TCP/IP DRIVER and LINK statements. If KEEPALIV=YES, a message is sent periodically to verify that a connection is still active. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information. To disable this function, specify KEEPALIV=NO on the DRIVER and LINK statements.

NWTCPHPS

A CONNECT function call to TCP/IP failed. The CONNECT function is used to connect to a remote Entire Net-Work node. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information. Make sure that the remote Entire Net-Work node is running and is accepting connections from this node.

NWTCPHPS

A SENDMSG function call to TCP/IP failed. The SENDMSG function is used to send a data packet to a remote Entire Net-Work node. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

A RECV function call to TCP/IP failed. The RECV function is used to receive a data packet from a remote Entire Net-Work node. This call waits for incoming data before returning to Entire Net-Work. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information.

NWTCPHPS

A GETHOSTBYNAME function call to TCP/IP failed. This type of function is used to determine the TCP/IP address of an Entire Net-Work node that used the ADJHOST parameter to specify the name. NETP600I will provide an error number that indicates why it failed.

Locate messages NETP600I and NETP601I for additional information. Make sure the name specified on ADJHOST parameter is correct and that this name is in the hosts file or domain name server. Read about the ADJHOST parameter

NWTCPHPS

A GetHostByAddr function call to TCP/IP failed, probably because the host name address was not defined in the DNS (Domain Name Service). The GetHostByAddr call is used to determine the name of a connecting IP address when ADJHOST has been specified on a LINK statement.

Add the host name and IP address to your domain name server.

NWTCPHPS

This message indicates an internal logic error in the HPS API.

Issue the TRACE and SNAP operator commands for the line driver.

For more information, see the section Entire Net-Work Operator Commands. Then contact your Software AG technical support representative.

NWTCPHPS

TCP/IP is being terminated on the local system. All connections using this driver will be disconnected. This is an informational message and does not indicate an error in Entire Net-Work.

Determine why the TCP/IP address space is being terminated.

NWTCPHPS

TCP/IP has terminated the connection for this link. Therefore, the link is no longer active.

Look for other messages on both the local and remote systems that will help you determine why the link was terminated.

NWTCPHPS

The asynchronous exit abended processing a previous TCP/IP function. This message indicates an internal logic error in the HPS API.

Issue the TRACE and SNAP operator commands for this driver.

For more information, see the section Entire Net-Work Operator Commands. Then contact your Software AG technical support representative.

NWTCPHPS

This message indicates an internal logic error in the HPS API.

Issue the TRACE and SNAP operator commands for this driver. For more information, see the section Entire Net-Work Operator Commands. Then contact your Software AG technical support representative.

NWTCPHPS

The asynchronous exit was entered without a required token. This message indicates an internal logic error in the HPS API.

Issue the TRACE and SNAP operator commands for this driver. For more information, see the section Entire Net-Work Operator Commands. Then contact your Software AG technical support representative.

NWTCPHPS

A call to the IBM TCP/IP stack failed for function xxxxxxxx. The error number nnnnn and the reason code rrrrrrrr indicate the reason the call failed, while sssss is the socket that the function failed on. This message provides diagnostic information about a previous error message. This message may also be followed by a NETP701I message that explains the error number and reason codes.

Locate message NETP701I for a description of the error number. Refer to the IBM documentation for an explanation of the error number and the reason code.

NWTCPOES

The text of this message describes the error number from message NETP700I.

Eliminate if possible the condition that caused this message.

NWTCPOES

An invalid request was made to this API.

Contact your Software AG technical support representative

NWTCPOES

An attempt to load a required module for TCP/IP failed. The driver and all links using this API will be unusable. This is most likely caused by TCP/IP not being correctly installed. It could also be caused by a short on storage condition or an I/O error.

Check the joblog and syslog for any additional messages that may indicate a reason for the problem. These messages may be operating system messages.

NWTCPOES

An attempt to allocate storage for a required control block failed. This control block is needed for the driver and all active links using this API. Only the new link being connected or the new driver being opened are affected. All active links and drivers will continue to run as long as the storage shortage does not cause other problems with Entire Net-Work

Look for other messages indicating storage problems and perform any action recommended.

NWTCPOES

An error occurred trying to close a socket used for a connection. The Entire Net-Work connection is closed, but this socket will be unusable for a future connection.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

A TCP/IP driver using API=OES has been closed. This is an informational message and does not indicate an error.

None

NWTCPOES

This message indicates that Entire Net-Work is not APF authorized. APF authorization is required in order to use the API=OES.

Provide APF authorization for all load libraries in the Entire Net-Work STEPLIB.

NWTCPOES

API=OES was specified for a driver on a system that does not support it. Currently OS390 is the only operating system that supports this API.

Specify a valid API for the system and TCP/IP stack you are running.

NWTCPOES

An Open Edition call to DUB the TCB failed. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

A call made to TCP/IP to get a new socket failed. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information. Some adjusting of parameters for TCP/IP may need to be done to allow for more sockets.

NWTCPOES

A BIND function call to TCP/IP failed. The BIND function is used to tell TCP/IP what port to listen on and what restrictions apply, i.e., who can connect to this port. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

A GETSOCKOPT function call to TCP/IP failed. The GETSOCKOPT function is used to determine the maximum message size that can be sent. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

A LISTEN function call to TCP/IP failed. The LISTEN function is used to set the number of connection requests that can be queued. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

An ACCEPT function call to TCP/IP failed. The ACCEPT function waits for a connection request and returns a socket to be used for the new conversation. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

A connect queue entry is needed to process a connection request and none is currently available. The connection request is rejected.

Increase the value of the CONNQUE parameter on the DRIVER statement.

NWTCPOES

A SETSOCKOPT function call to TCP/IP failed. The SETSOCKOPT function is used to set the KEEPALIVE option in TCP/IP. KEEPALIVE is a TCP/IP option that regularly sends a message to verify that a connection is still active. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information. Set KEEPALIVE=NO parameter on driver and link statements to disable this function.

NWTCPOES

A SETSOCKOPT function call to TCP/IP failed. The SETSOCKOPT function is used to set the REUSEADDR option in TCP/IP so that a socket can be reused immediately after being closed.

Locate messages NETP700I and NETP701I for additional information. .

NWTCPOES

A CONNECT function call to TCP/IP failed. The CONNECT function is used to connect to a remote Entire Net-Work node. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information. Make sure that the remote Entire Net-Work node is running and is accepting connections from this node.

NWTCPOES

A SENDMSG function call to TCP/IP failed. The SENDMSG function is used to send a data packet to a remote Entire Net-Work node. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

A RECV function call to TCP/IP failed. The RECV function is used to receive a data packet from a remote Entire Net-Work node. This call waits for incoming data before returning to Entire Net-Work. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information.

NWTCPOES

A GETHOSTBYNAME function call to TCP/IP failed. The GETHOSTBYNAME function is used to determine the TCP/IP address of an Entire Net-Work node that used the ADJHOST parameter to specify the name. NETP700I will provide an error number that indicates why it failed.

Locate messages NETP700I and NETP701I for additional information. Make sure that the name specified on ADJHOST parameter is correct and that this name is in the hosts file or domain name server. Read about the ADJHOST parameter

NWTCPOES

A GetHostByAddr function call to TCP/IP failed, probably because the host name address was not defined in the DNS (Domain Name Service). The GetHostByAddr call is used to determine the name of a connecting IP address when ADJHOST has been specified on a LINK statement.

Add the host name and IP address to your domain name server.

NWTCPOES

This message indicates an internal logic error in the OES API.

Issue the TRACE and SNAP Entire Net-Work commands for this driver. Then contact your Software AG technical support representative.

NWTCPOES

TCP/IP is being terminated on the local system. All connections using this driver will be disconnected. This is an informational message and does not indicate an error in Entire Net-Work.

Determine why the TCP/IP address space is being terminated.

NWTCPOES

TCP/IP has terminated the connection for this link. This link is no longer active.

Look for other messages on both the local and remote systems to determine why the link was terminated.

NWTCPOES

The asynchronous exit abended while processing a previous TCP/IP function. This message indicates an internal logic error in the OES API.

Issue the TRACE and SNAP Entire Net-Work commands for this driver. Then contact your Software AG technical support representative.

NWTCPOES

This message indicates an internal logic error in the OES API.

Issue the TRACE and SNAP Entire Net-Work commands for this driver. Then contact your Software AG technical support representative.

NWTCPOES

The asynchronous exit was entered without a required token. This message indicates an internal logic error in the OES API.

Issue the TRACE and SNAP Entire Net-Work commands for this driver. Then contact your Software AG technical support representative.

NWTCPOES

The Simple Connection Line Driver's Active Client Table (ACT) array was allocated at the indicated address. This message is issued at initialization, and also if the ACT array is expanded.

None required. This message is informational only.

NETTCPX, NXTSRV

Allocation of a client control block failed. Possible causes are:

• shortage of storage

• exceeding the total number of clients allowed (32767)

• internal error

Increase storage or limit the number of clients.

NXTSRV

An internal error occurred when attempting to free a client control block.

Contact your Software AG technical support representative.

NETTCPX

The Active Client Table (ACT) array has been increased because it was full and a new client attempted to initialize. The table is increased by 50% of its current size.

If this message occurs frequently, increase NUMUSERS to minimize expansions.

NXTSRV

Each incoming request is validated against that client's current information. This message is issued if there was a mismatch or the client was not found.

Collect traces on the client and server side and contact your Software AG technical support representative.

NETTCPX

An error occurred when converting the message to Entire Net-Work's MHDR format. The probable cause is a shortage of storage.

If increasing storage does not resolve the error, contact your Software AG technical support representative.

NETTCPX

An invalid value was specified for NUMUSERS. Entire Net-Work sets NUMUSERS to 100 and continues to initialize.

Correct the NUMUSERS value.

NETTCPX

The CONNECT command is not allowed with the Simple Connection Line Driver. Connect processing is handled automatically when a client initiates.

No action is required for this informational message.

NETTCPX

Client xxxxx was terminated before the current reply could be sent back, where xxxxx is the ACT index and the rightmost two bytes of the Context ID in the A1 message header. This can happen if the client times out or otherwise terminates while Entire Net-Work is processing a reply for that client.

If the client did not legitimately time out or terminate, obtain traces and contact your Software AG technical support representative.

NETTCPX

The attempt failed to load the module named in the message (modname). This module is required for SSL support. The driver fails to open.

Make sure this module is available to the Entire Net-Work job.

SSL support for the driver named in the message (drvname) has been successfully initialized.

No action is required for this informational message.

Initialization of SSL support failed for the driver named in the message (drvname) with the internal return code shown in the message (code). The driver is not opened.

Contact your Software AG customer support representative for assistance.

The SSL function named in the message (sslfunction) failed with the displayed return code (code) for the link named in the message (lnkname).

Contact your Software AG customer support representative for assistance.

An invalid value was specified for the SSLVRS parameter.

Specify a valid value for the parameter and try again.

An invalid value was specified for the SSLVRF parameter.

Specify a valid value for the parameter and try again.

The link named in the message was successfully connected to the partner TCP/IP address named in the message.

This message is issued for TCPX links in place of NET0110. It is written only to DDPRINT/NETPRNT, not the console.

Normal processing continues and the newly connected link can be used for message traffic.

None required. This message is informational only.

The link named in the message was disconnected from the partner TCP/IP address named in the message by one of the following events:

• The node terminated.

• A DISCONNECT operator command was issued.

• One of several types of link failures occurred (these link failures are described by related line driver messages)

• The partner TCP/IP address terminated the socket connection.

This message is issued for TCPX links in place of NET0107. It is written only to DDPRINT/NETPRNT, not the console.

The system continues processing without the link. If the disconnection was due to an error, other messages should indicate the cause of the disconnection.

Correct the error, if required, and retry the application.

An error occurred attempting to notify the SSL subtask to process a new connection. The connection fails for the specified link.

This is an internal error. Contact your Software AG customer support representative.

The SslSetSession function failed with the return code displayed in the message (code).

Check your SSL configuration and try again.

On z/OS systems, only API=OES can be used with the SSL driver.

Specify API=OES and restart.

This message displays various informational messages during SSL initialization.

No action is required for this informational message.