ADACNV Error Messages

Version number specified with parameter "TOVERS" is not supported by ADACNV.

Change the parameter to a supported version and rerun the utility.

The current version of the database is 5.1 or below. Conversion could only be performed from version 5.2 and above.

Convert the database to version 5.2 by starting and stopping the version 5.2 Adabas nucleus, then rerun ADACNV.

The DIB block is not empty, conversion is not possible.

Shut down the Adabas nucleus, wait for all utilities to complete, and rerun ADACNV.

The CP block extension (RABN 20-24) is not empty. Conversion to version 5.2 is not possible.

To clear the CP block extension, restart the nucleus; then end the nucleus normally.

The Work data set is not empty. Conversion is not possible.

To remove the pending autorestart, restart the nucleus and end it normally.

The DDFILEA block size ("blocksize" bytes) is too small to write a record with a length of "length" bytes.

Assign DDFILEA to a device type with a larger sequential block size.

Security-by-value conversion expands the data records, which then do not fit into the data block.

Run ADAORD REORDATA on the security file with a larger padding factor; then rerun the ADACNV job.

One of the following version 6 features was used:

• 4-byte RABN

• DBID greater than 255

• maximum number of files in the database more then 255

Conversion to version 5 is not possible.

Remove version 6 features and rerun the ADACNV job.

Version 6 feature 4-byte ISN was used. Conversion to version 5 is not possible.

Remove version 6 features and rerun the ADACNV job.

The Adabas Delta Save Facility was used. ADADSF cannot run under version 5.2.

Switch ADADSF off and rerun the ADACNV job.

Version 5.3 feature was used. Conversion to version 5.2 is not possible.

Remove version 5.3 features and rerun the ADACNV job.

DDFILEA (FILEA) has an invalid structure. This is probably a job control (JCL) statement error.

Correct any error and rerun the ADACNV job.

Version 7.1 feature was used. Conversion to version 6 is not possible.

Remove version 7.1 features and rerun the ADACNV job.

The PLOGRn data set is not free. Conversion fails.

Run ADARES PLCOPY to free the PLOG data set(s); then rerun the ADACNV job.

Alternate RABNs are not supported by Adabas version 7.2 and above.

Use ADAORD to reorder the database before converting it from a version of Adabas version 7.1 or below to Adabas version 7.2 or above.

The parallel participant table (PPT) entry contains a protection log (PLOG) data set with the specified number and name. ADACNV was unable to open the data set. The data set may have been deleted, or it may not be cataloged, or it may contain PLOG data that has not yet been copied.

Provide access to the specified data set or use the IGNPPT parameter and rerun the job.

The parallel participant table (PPT) entry contains a protection log (PLOG) data set with the name and number specified. ADACNV was unable to read the first block of this data set. The data set has probably been destroyed.

Determine the cause of the error; correct it and rerun the job.

Backward conversion of an Event Replicator database is not supported prior to Adabas version 7.4.

Investigate the cause of the error.

Backward conversion of a database is not possible when a Replicator or SLOG system file is loaded.

Investigate the cause of the error.

The allocation of the PPT area failed. An attempt was made to allocate 32 ASSO blocks.

Correct the error and rerun the job.

The database has more than five physical ASSO or DATA extents. It cannot be reverted back to an Adabas 7 database.

Contact your Software AG technical support representative for assistance.

One or more system file numbers is greater than 255.

Adjust the system file numbers so they are less than 255 and try again.

An Adabas 8 feature is used by the file listed in the message that makes it impossible to revert the database to a prior Adabas release.

Remove the Adabas 8 features and rerun the ADACNV job.

The Adabas version of the database is the same as the version requested in the ADACNV run.

No action is required for this informational message.

Adabas 7 allowed a maximum of six user system files (files loaded with the SYSFILE option). More than six user system files currently exist.

Unload, delete, and reload the additional user system files without the SYSFILE option. Then rerun this utility.

The user system file identified in the message (nnnnn) exists in the reserved area of the GCB.

Unload, delete, and reload the system file with the SYSFILE option to place the file number in the correct area of the GCB. Then rerun this utility.

In the first phase of conversion, this message is printed to indicate that the conversion of the database is possible.

The ADACNV utility has begun its final pass. Any abend after this point requires a new run of the utility with the RESTART parameter.

In the first phase of conversion, a conversion step has started.

The conversion step has been successfully completed.

Adabas Reflective Database is not supported by Adabas version 7 and above.

Alternate RABNs are not supported by Adabas version 7.2 and above.

Security-by-value conversion has been successfully completed.

At least one FST entry does not fit into one FST block due to the FST structure change. The entry or entries with the smallest RABN range(s) are deleted.

ADACNV finishes with a warning and response code 4.

Run ADAORD REORDB after conversion.