You can modify the configuration parameters set for a specific client using SMH. These parameters are stored in the appropriate client configuration file on the local machine. For more information, read About Client Configurations.
Note:
We do not recommend that you maintain client configuration files using
a text editor. Instead, we recommend that you use SMH to perform all
maintenance to Entire Net-Work configuration files.
To maintain the configuration parameters for a client in SMH:
Make sure you have accessed the System Management Hub.
Select and expand Entire Net-Work Client from the list in tree-view to access the Entire Net-Work Client administration area.
Select and expand Clients from the Entire Net-Work Client sublist.
A list of machine names appears. The machines listed are computers on which clients managed by this installation of the System Management Hub are defined.
Select and expand the client machine on which the client is defined.
The client configuration section becomes available in tree-view.
Right-click on the client configuration whose parameters you want to maintain and select from the resulting drop-down list.
Or:
Select the client configuration and then select from the
menu of SMH.
The Client Configuration Parameters panel appears in detail-view.
Modify the parameters on the Client Configuration Parameters panel, as described in the following table. When all parameters are set as you want, click to save them.
| Parameter | Description |
|---|---|
| ACCEPTED_DBIDS | Specify the database IDs you want this client to be able to access. If more than one database ID is needed, separate them with commas. If a range of database numbers is needed, separate them with a dash. For example, "4,12-15,62" indicates that the client should have access to databases 4, 62, and any databases with numbers between 12 and 15 (inclusive). For more information, read Understanding Filtering. |
| ADABAS_TIMEOUT | Specify the number of seconds the client should wait for a response from a remote Adabas call before it times out. The default is 60 seconds; the minimum value you can specify is 5 seconds. |
| Full LNK Trace | Click in this checkbox to set the LNKTRACE value to obtain full tracing of ADALNK processing. Do not check this checkbox unless specifically instructed to do so by a Software AG Customer Support representative. If you do, your installation could be overrun with trace messages that would be meaningless to you and would likely affect system performance. |
| Full XTS Trace | Click in this checkbox to set the XTSTRACE value to obtain full tracing of Software AG transport services processing. Do not check this checkbox unless specifically instructed to do so by a Software AG Customer Support representative. If you do, your installation could be overrun with trace messages that would be meaningless to you and would likely affect system performance. |
| LNKTRACE | Set the ADALNK trace level using this
parameter. The default value is "0". Do not alter
this setting unless specifically instructed to do so by a Software AG Customer
Support representative.
For more information about Entire Net-Work Client tracing, read Tracing Entire Net-Work Client Processing. |
| REJECTED_DBIDS | Specify the database IDs you do not want this client to be able to access. If more than one database ID is needed, separate them with commas. If a range of database numbers is needed, separate them with a dash. For example, "4,12-15,62" indicates that the client should not have access to databases 4, 62, and any databases with numbers between 12 and 15 (inclusive). For more information, read Understanding Filtering. |
| REMEMBER_DBID | Indicate whether the access entries for databases used by this client should be remembered and stored in local Entire Net-Work Client access entries in the Entire Net-Work Client configuration file. Valid values are "YES" and "NO". If you specify "YES", the access entry information is stored locally; if you specify "NO", the access entry information is available only in the Directory Server configuration file, wherever the Software AG Directory Server is installed. |
| USER_EXITS | Specify the name of the user exit DLL file that should be used with this client. For more information about Entire Net-Work Client user exits, read Understanding the User Exit Interface. |
| WCPPARTITION | Specify the partition in which the client is assigned, if any. For more information, read Understanding Partitioning. |
| XTSTRACE | Set the Software AG transport services trace
level using this parameter. The default value is
"0". Do not alter this setting unless specifically
instructed to do so by a Software AG Customer Support representative.
For more information about Entire Net-Work Client tracing, read Tracing Entire Net-Work Client Processing . |
The client parameters are updated in the appropriate Entire Net-Work Client configuration file.
