This document covers the following topics:
This chapter describes the steps necessary to install the Adabas Bridge for DL/I (ADL) in a z/OS environment. After performing these steps, you will be able to run the ADL data base conversion utilities, to use the ADL Online Services and to operate the ADL Interfaces for DL/I and Adabas calls.
For easy reference, all installation steps are summarized below. In general, all steps must be performed in all environments. Exceptions are clearly marked as such in the detailed description of the individual steps.
| Step | Description |
|---|---|
| Step 1 | Load the ADL libraries to disk. |
| Step 2 | Load the ADL directory file. |
| Step 3 | Load the ADL Online Services and the ADL Installation Verification Package. |
| Step 4 | Create the ADL parameter module. |
| Step 5 | Create the executable ADL data conversion module. |
| Step 6 | Create the executable ADL precompiler module. |
| Step 7 | Create the executable module for the ADL CALLDLI Interface in batch. |
| Step 8 | Create the executable module for the ADL Consistency Interface in batch. |
| Step 9 | Create the executable module for the ADL Interfaces under CICS. |
| Step 10 | Create the executable ADL batch region controller. |
| Step 11 | Create the ADL substitute for the Adabas link module in batch. |
| Step 12 | Link-edit the Adabas link module under CICS with the ADL exit
ADLEXITB.
|
Note:
If you use Software AG's System Maintenance Aid (SMA), steps 1 to 9
are performed by SMA.
Load the ADL libraries to disk using the JCL given below as an example.
The table below gives an estimate of how much space is needed for various device types (primary cylinders, directory tracks).
| Library | 3390 |
|---|---|
| Load | 3, 10 |
| Source | 6, 36 |
| LC23 | 1, 2 |
Note:
If you are using SMA, refer to the System Maintenance
Aid documentation. If you are not using SMA, follow the instructions
below.
This section explains how to copy all data sets from tape to disk. You will then need to perform the individual installation procedure for each component to be installed.
The data set COPY.JOB contains the JCL required to copy all
data sets from tape to disk. Copy COPY.JOB to your disk by using
the following sample JCL:
//SAGTAPE JOB SAG,CLASS=1,MSGCLASS=X //* --------------------------------- //COPY EXEC PGM=IEBGENER //SYSUT1 DD DSN=COPY.JOB, // DISP=(OLD,PASS), // UNIT=(CASS,,DEFER), // VOL=(,RETAIN,SER=tape-volume), // LABEL=(2,SL) //SYSUT2 DD DSN=hilev.COPY.JOB, // DISP=(NEW,CATLG,DELETE), // UNIT=3390,VOL=SER=volume, // SPACE=(TRK,(1,1),RLSE), // DCB=*.SYSUT1 //SYSPRINT DD SYSOUT=* //SYSIN DD DUMMY //
where:
hilev is a valid high level
qualifier
tape-volume is the tape
volume name, for example: T12345
volume is the disk volume
name
Modify COPY.JOB according to your local naming conventions
and set the following disk space parameters:
Set HILEV to a valid high level qualifier.
Set LOCATION to a storage location.
Set EXPDT to a valid expiration date.
Submit COPY.JOB to copy all data sets from tape to your
disk.
Load the ADL Directory File. This file is a standard Adabas file
unloaded with the ADAULD utility of Adabas. You may use the JCL in
the ADL source library member ADLINS2 as an example.
If ADL is already installed at your site, and you want to continue to
use the existing ADL directory file, you may simply delete the obsolete error
messages from the existing Directory File and load the new messages from the
unloaded file provided on the installation tape. You may use the JCL in the ADL
source library member ADLINS2A as an example.
Load the ADL Online Services and the DDM for the ADL
Directory File, ADB-CONTROL. The INPL file on the
installation tape was created with the Natural SYSOBJH utility and
is compatible with Natural version 4.1 and upwards. You may use the JCL in the
ADL source library member ADLINS3 as an example.
Note that the INPL file on the ADL installation tape
contains a DDM for the ADL Directory File and the object modules
of the library SYSADL with the ADL-supplied subprograms
ADLERROR and ADLACTIV. These subprograms may be used
by Natural applications operating under the ADL Consistency Interface.
The same step loads also the ADL Installation Verification Package
(SYSADLIV) and the related DDMs.
Create the ADL parameter module (DAZPARM) by assembling the
DAZPARM macro. This procedure is common to both z/OS and z/VSE and
is described in the chapter ADL
Parameter Module in this documentation.
You may use the JCL in the ADL Source Library member
ADLINS4 as an example.
The following steps are performed:
Create the executable ADL CBC utility module by running
the link editor and specifying the following link edit directives:
ORDER DAZPARM INCLUDE ADLLOAD(DAZPARM) INCLUDE ADLLOAD(DAZCCGEN) INCLUDE ADLLOAD(DAZCCOUT) INCLUDE ADLLOAD(DAZCCSUB) INCLUDE ADLLOAD(DAZAXES) INCLUDE ADLLOAD(DAZSERV) INCLUDE ADLLOAD(DAZDEBUG) INCLUDE ADLLOAD(DAZZAP) NAME DAZNUCU(R)
You may use the JCL in the ADL Source Library member
ADLINS5U as an example.
This step need only be performed where one or more of the application
programs to be converted uses the HLPI.
Create the executable ADL precompiler module by running the link editor and specifying the following link edit directives:
ORDER DAZPARM INCLUDE ADLLOAD(DAZPARM) INCLUDE ADLLOAD(DAZEXEC) INCLUDE ADLLOAD(DAZSERV) INCLUDE ADLLOAD(DAZLANP) INCLUDE ADLLOAD(DAZSYXTB) INCLUDE ADLLOAD(DAZDEBUG) INCLUDE ADLLOAD(DAZZAP) NAME DAZNUCP(R)
You may use the JCL in the ADL Source Library member
ADLINS6P as an example.
Create the executable ADL CALLDLI Interface batch module
by running the link editor and specifying the following link edit directives.
This step must also be performed when installing under IMS/TP:
ORDER DAZPARM INCLUDE ADLLOAD(DAZPARM) INCLUDE ADLLOAD(DAZBENT) INCLUDE ADLLOAD(DAZAXES) INCLUDE ADLLOAD(DAZSERV) INCLUDE ADLLOAD(DAZINICB) INCLUDE ADLLOAD(DAZCDPOS) INCLUDE ADLLOAD(DAZDREIN) INCLUDE ADLLOAD(DAZDEBUG) INCLUDE ADLLOAD(DAZZAP) NAME DAZNUCB(R)
You may use the JCL in the ADL source library member
ADLINS7B as an example.
Create the executable ADL Consistency Interface module for batch by running the linkage-editor and specifying the following link-edit directives:
ORDER DAZPARM INCLUDE ADLLOAD(DAZPARM) INCLUDE ADLLOAD(DAZAXES) INCLUDE ADLLOAD(DAZBDOKE) INCLUDE ADLLOAD(DAZBRQH) INCLUDE ADALOAD(ADAUSER) INCLUDE ADLLOAD(DAZCDPOS) INCLUDE ADLLOAD(DAZCONSI) INCLUDE ADLLOAD(DAZDEBUG) INCLUDE ADLLOAD(DAZDREIN) INCLUDE ADLLOAD(DAZINICB) INCLUDE ADLLOAD(DAZSERV) INCLUDE ADLLOAD(DAZZAP) NAME DAZNUCA(R)
You may use the JCL in the ADL source library member
ADLINS8A as an example.
The ADAUSER object module must be included from a valid
Adabas load library.
Note:
Whenever you want the user written user exit (DAZUEX01)
to become active in batch you must, in addition, include your user exit
DAZUEX01 within the ADL nucleus DAZNUCA. This may be
achieved by specifying an extra statement for the linkage-editor input:
INCLUDE USRLOAD(DAZUEX01)
See the section ADL User Exit
DAZUEX01 later in this documentation for more details on
the purpose and conventions for the user exit DAZUEX01.
Create the executable ADL Interfaces CICS module by running the link editor and specifying the following link edit directives:
INCLUDE CICLOAD(DFHEAI) INCLUDE CICLOAD(DFHEAI0) INCLUDE ADLLOAD(DAZPARM) INCLUDE ADLLOAD(DAZCAPRI) INCLUDE ADLLOAD(DAZCIFP) INCLUDE ADLLOAD(DAZCLUB) INCLUDE ADLLOAD(DAZCRQH) INCLUDE ADLLOAD(DAZCDOKE) INCLUDE ADLLOAD(DAZCONSI) INCLUDE ADLLOAD(DAZAXES) INCLUDE ADLLOAD(DAZSERV) INCLUDE ADLLOAD(DAZINICB) INCLUDE ADLLOAD(DAZCDPOS) INCLUDE ADLLOAD(DAZDREIN) INCLUDE ADLLOAD(DAZDEBUG) INCLUDE ADLLOAD(DAZSTUB) INCLUDE ADLLOAD(DAZZAP) ENTRY DAZPARM NAME DAZNUCC(R)
You may use the JCL in the ADL source library member
ADLINS9C as an example.
Note:
The ADL load library contains modules which are CICS release
dependent. The members in the standard load library are for CICS TS 3.1 and
CICS TS 3.2. When you run under CICS TS 2.3 or below, the ADL.LC23 library must
be concatenated in front of the ADL load library.
Note:
Whenever you want the user written user exit (DAZUEX01)
to become active under CICS, you must, in addition, include your user exit
DAZUEX01 within the ADL Interfaces CICS nucleus,
DAZNUCC. This may be achieved by specifying an extra statement for
the linkage-editor input:
INCLUDE USRLOAD(DAZUEX01)
See the section ADL User Exit
DAZUEX01 later in this documentation for more details on
the purpose and conventions for the user exit DAZUEX01.
Create the executable ADL batch region controller by running the linkage-editor and specifying the following link-edit directives:
ENTRY DAZBIFP INCLUDE ADLLOAD(DAZBIFP) INCLUDE ADLLOAD(DAZBRQH) INCLUDE ADALOAD(ADAUSER) INCLUDE USRLOAD(DAZUEX01) NAME DAZIFP(R)
You may use the JCL in the ADL source library member
ADLINS10 as an example. The ADL load library, the Adabas load
library and the user load library must be defined with the file names
ADLLOAD, ADALOAD and USRLOAD, respectively.
Note:
This step has to be performed only if you want a user written user
exit (DAZUEX01) to become active in batch. See the section
ADL User Exit
DAZUEX01 later in this documentation for more details on
the purpose and conventions for this user exit.
Note:
This step is only required if you plan to use the ADL Consistency
Interface in batch.
Assemble and link-edit the ADL substitute for the Adabas link module in
batch, ADALNK. You may use the JCL in the ADL source library
member ADLINS11 as an example. You need to perform this step only
if you plan to use the ADL Consistency Interface. See the section
Batch
Installation and Operation in the ADL
Interfaces documentation for more information on how to install the
ADL Consistency Interface.
The ADL source library member to be assembled is DAZLNKO.
Before the assembly, you will have to customize the assembler local variable
&ADALNK in the ADL source library member DAZLNKO.
&ADALNK specifies the new name chosen for the original Adabas
link module which must be renamed. It is defaulted to
"ADAOLK".
Note that the ADL source library, the Adabas source library and the system macro libraries must be concatenated in the given order.
If you want to make use of the table of converted Adabas files
(DAZTCF) you have to perform the steps described in section
Batch
Installation and Operation in the ADL
Interfaces documentation. Assemble DAZTCF before
link-editing ADALNK. The assembly of DAZTCF is
included in the sample JCL ADLINS11. Add the following statement
to the linkage-editor input for the Adabas batch link module:
INCLUDE ADLLOAD(DAZTCF)
For Adabas version 8 and above, you must additionally link the Adabas link-globals-table LNKGBLS to the ADL substitute:
INCLUDE ADALOAD(LNKGBLS)
This step is only required if you plan to use the ADL Consistency Interface under CICS. See the section CICS Installation and Operation in the ADL Interfaces documentation for more information on how to install the ADL Consistency Interface.
Add the following statement to the linkage-editor input for the Adabas link module under CICS or, for Adabas version 8, to the linkage-editor input for the Adabas globals module:
INCLUDE ADLLOAD(ADLEXITB)
If you want to use the table of converted Adabas files, assemble the
DAZTCF table and include this also:
INCLUDE ADLLOAD(DAZTCF)
Note:
The parameter LUSAVE in the Adabas link
source member LNKOLSC must have a value of at least 72 bytes. For
Adabas Version 8 and above set the “ADL” parameter in the LGBLSET macro to
“YES”.
